Step 7,8:
Please apply silicone sealants to the inner and outer edges of parts
7043 + 7042
as well as to the
middle of parts
7029 + 7039
in order to prevent water from seeping in.
Step 16:
Please apply silicone sealants above beam
7288 + 7289,
in order to prevent water from seeping in.
Step 18
: Make sure that the angle between the back wall profile and the panel supporting profiles is 90 degrees.
Assembly of the panels should start from the middle of the patio cover to each side alternately.
Step 27
: Please adjust the poles (inside out and sideways) by sliding them to their final position prior to anchoring.
Make sure that the poles distance from the Patio cover side edge does not exceed
54 cm/21.3”.
*Please note:
Anchoring this product to the ground is essential to its stability and rigidity. It is required to complete
this stage in order for your warranty to be valid.
(Step 28)
* Tighten all screws when completing assembly.
EN
Notes During Assembly
Steps
0-54cm
0”-21
¼
”
0-54cm
0”-21
¼
”
0-54cm
0”-21.3”
0-54cm
0”-21.3”
A
B1
B2
13
º
17
º
C
15_05_V4
•
Use a soft platform below the parts to avoid scratches and damages.
•
Product dimensions can be adjusted to your specific needs:
1.
The wall-mounting profile (top-back) can be adjusted from
260 to 305 cm (102.4” to 120”)
above ground.
The adjusting is done when measuring and drilling
(Step 9)
.
Please note the installation recommendations’ height suggested in
Diagram A
.
It is possible to fix the Patio Cover back wall height at the lowest point of
260 cm/102.4”
. This method is optional if
the assembly conditions and exterior walls do not allow to follow the suggested installation as appears in the manual.
Please note that the product appearance may slightly change as a result, however snow load weight does not change.
2.
Poles distance from the wall can be adjusted from
226 to 286 cm (89” to 112.5”)
as suggested in
Diagram B1
.
Poles distance from the side edges can be adjusted from
0 to 54 cm (0” to 21.3”)
as suggested in
Diagram B2
.
The adjusting is done after assembly and before anchoring
(Step 27)
by sliding poles and profile
7030 +7031
at the
roof profiles’ channels.
3.
Wall mounting and distance from the wall determine the roof angle and the total depth of the product (distance of
gutter from the wall). Higher wall mounting and shorter distance between wall and poles increase the roof angle and
shorten the total depth as suggested in
Diagram C
.
226-286cm
89” - 112.5”
260-305cm
102.4”-120”
Note:
The wall anchoring kit supplied with this product is suitable only for concrete walls.
Other wall types need an accordant wall fixation kit. (Contact your supplier)
Summary of Contents for Feria
