background image

2

BENTO 42 E | Owner and Installation Manual

SAFETY INFORMATION

 WARNINGS:

IMPORTANT: This appliance should 

be inspected before use and at 

least once annually by a qualified 

service person.

More frequent cleaning may 

be required as necessary. It 

is imperative that the control 

compartment, burners and 

circulating air passageways of the 

appliance be kept clean.

DANGER: Carbon monoxide 

poisoning can lead to death!

CARBON MONOXIDE POISONING:

Early signs of carbon monoxide 

poisoning resemble the flu, with 

symptoms including headache, dizziness, 

or nausea. If you experience these signs, 

the Fire Pit may not be working properly. 

Get fresh air at once! Have the Fire Pit 

serviced. Some people are more affected 

by carbon monoxide than others, 

including pregnant women, people with 

heart or lung disease or anemia, those 

under the influence of alcohol, and those 

at high altitudes.

NATURAL GAS AND PROPANE: 

To assist in detecting leaks, an odorant 

has been added to natural gas and 

propane. However, this odorant can fade, 

and gas may be present even though no 

odor exists. Make certain you read and 

understand all warnings. Keep this manual 

for reference. It is your guide to safe and 

proper operation of this appliance.

WARNING:

 Any modification to this appliance or its 

controls can be dangerous.

1.  This appliance, as supplied, is only for use with the 

type of gas indicated on the rating plate.

2.  When this appliance is connected to a fixed piping 

system, the installation must conform to local codes, 

or in the absence of local codes, to the National 

Fuel Gas Code, ANSI Z223.1/NFPA 54, or the 

International Fuel Gas Code.

3.  Keep the appliance area clear and free from 

combustible materials, gasoline and other flammable 

vapors and liquids

4.  Do not burn solid fuel in this appliance. Do not use 

this appliance to cook food or to burn paper or other 

objects.

5.  Children and adults should be alerted to the 

hazards of high surface temperatures and should 

stay away to avoid burns or clothing ignition.

6.  Clothing or other flammable materials should not 

be hung from the appliance, or placed on or near 

the appliance.

7.  Young children should be carefully supervised 

when they are in the area of the appliance.

8.  Do not use the appliance if any part has been under 

water. Immediately call a qualified service technician 

to inspect the appliance and to replace any part of 

the control system and any gas control which has 

been under water.

9.  Inspect the appliance before each use.

10. Turn the appliance off and let cool before servicing, 

installing, repairing or covering. Any guard or other 

protective device removed for servicing the 

appliance must be replaced prior to operating the 

appliance. Only a qualified service person should 

install, service, or repair the appliance.

HIGH ALTITUDE INSTALLATION

The appliance is rated for installations up to 4500’ (1372 

m) above sea level. Above 4500’ the appliance must be 

derated at the factory for the appropriate altitude unless 

the local fuel is pre derated.

LOCAL CODES

Install and use your Outdoor Fire Pit with care. Follow 

local codes. In the absence of local codes, use the latest 

edition of The National Fuel Gas Code ANSI Z223.1/

NFPA 54 available from:

American National Standards Institute Inc.

1430 Broadway

New York NY 10018

National Fire Protection Association, Inc.

Batterymarch Park

Quincy MA 02269.

Summary of Contents for Bento 42 E




















Reviews: