background image

INSTALLER: Leave this manual with the appliance. CONSUMER: Retain this manual for future reference

Burner conforms to:  ANSI Z21.97/CSA 2.41 - (2012/10/01) “Outdoor Decorative Gas Appliances”

We recommend that our fire pits be 

installed and serviced by professionals 

that are certified in the U.S. by NFI 

(National Fireplace Institute)

OUTDOOR FIREPIT BURNER MODELS CIR-E-18 & 18P

DANGER - IF YOU SMELL GAS

1. Shut off gas to the appliance. 

2. Extinguish any open flame. 

3. If odor continues, keep away from the appliance and immediately call your gas   

    supplier or fire department.

WARNING

Do not store or use gasoline or other flammable vapors and liquids in the vicinity 

of this or any other appliance.  An LP-cyllinder not connected for use shall not be 

stored in the vicinity of this or any other appliance.

CARBON MONOXIDE HAZARD

This appliance can produce carbon monoxide which has no odor. 

Using it in an enclosed space can kill you. 

Never use this appliance in an enclosed space such as a camper, tent, 

car or home.

WARNING:

Improper installation, adjustment, alteration, service or maintenance can cause 

injury or property damage. Read the installation, operating and maintenance 

instructions thoroughly before installing or servicing this equipment.

WARNING: FOR OUTDOOR USE ONLY!

DANGER

BENTO 42 FIRE PIT 

Electronic Ignition

 |

 Installation Manual

Summary of Contents for Bento 42 E




















Reviews: