background image

4

Palmgren Operating Manual & Parts List

80177

INSTALL THE HEAD

Refer to Figure 9/10.

WARNING: 

Although compact, the drill press head assembly 

is heavy. Two people are required to mount the drill press head 
assembly onto the column.

● 

Carefully lift the head above the column and slide it onto the 
column. Make sure the head slides down over the column as far 
as possible. Align the head with the base.

● 

Using the 5 mm hex wrench, tighten the two head lock set 
screws (Ref. No. 70) on the right side of the head.

ATTACH BELT TENSION HANDLE

Refer to Figure 8.

● 

Thread handle (Ref. No. 183) into motor mount plate (Ref. No. 
184).

MOUNT QUILL FEED HANDLE ASSEMBLY

Refer to Figure 8.

● 

Place key (Ref. No. 146) into feed shaft assembly (Ref. No. 61).

● 

Place quill feed handle assembly (Ref. No. 147) to the feed shaft 
assembly.

● 

Secure quill feed handle assembly with a flat head screw (Ref. No. 
150) and a washer (Ref. No. 149).

● 

Thread handle bar (Ref. No. 151) into quill feed handle assembly 
(Ref. No. 147).

INSTALL THE CHUCK

Refer to Figure 8.

WARNING:

 

Before any assembly of the chuck and arbor to the drill 

press head, clean all mating surfaces with a nonpetroleum based 
product, such as alcohol or lacquer thinner. Any oil or grease used 
in the packing of these parts must be removed otherwise the chuck 
may come loose during operation.

● 

Place the chuck (Ref. No. 131) onto the spindle arbor (Ref. No. 
134) while lowering the spindle by turning the feed handles (Ref. 
No. 147) counterclockwise, until the slot appears on the quill.

● 

Push the chuck and spindle arbor up into the spindle, making sure 
the tang is engaged and locked in the inner slot of the spindle. 
Once tang is oriented correctly, drill duck will not rotate without 
turning the spindle.

● 

Open the jaws of the chuck (Ref. No. 131) by rotating the chuck 
sleeve clockwise. To prevent damage, make sure the jaws are 
completely receded into the chuck.

 

NOTE:

 Clean the taper with a non-alcohol based cleaner before 

inserting it into the arbor.

● 

Using a rubber mallet, plastic-tipped hammer, or a block of wood 
and a hammer, firmly tap the chuck upward into position on the 
spindle shaft. 

CHUCK KEY STORAGE 

Refer to Figure 8, 9/10.

● 

Storage holder (Figure 9/10, Ref. No. 68) for the chuck key (Figure 
8, Ref. No. 132) is located on the right side of the head.

MOUNT DRILL PRESS

● 

Drill press must be mounted to flat level surface. Use shims or 
machine mounts if necessary. Do not mount drill press in 

 

direct sunlight.

● 

Be sure to bolt drill press to floor or bench securely to prevent 
tipping and minimize vibration.

● 

Tighten all nuts and bolts that may have loosened during 
shipment.

POWER SOURCE

The motor is designed for operation on the voltage an frequency 
specified. Normal loads will be handled safely on voltages not more 
than 10% above or below the specified voltage.
Running the unit on voltages which are not within the range may 
cause overheating and motor burn out. Heavy loads require that the 
voltage at motor terminals be no less than the voltage specified.

GROUNDING INSTRUCTIONS

Refer to Figure 2, 3 and 4.

WARNING:

 Improper connection of equipment grounding 

conductor can result in the risk of electrical shock. Equipment 
should be grounded while in use to protect operator from electrical 
shock. Check with a qualified electrician if grounding instructions 
are not understood or if in doubt as to whether the tool is properly 
grounded.
This tool is equipped with an approved 3-conductor cord rated 
up to 300 V and a 3-prong grounding type plug rated at 115 V for 
your protection against shock hazards.
Grounding plug should be plugged directly into a properly 
installed and grounded 3-prong grounding-type receptacle, as  
shown (Figure 2).

Do not remove or alter grounding prong in any manner. In the event 
of a malfunction or breakdown, grounding provides a path of least 
resistance for electrical shock. 

WARNING: 

Do not permit fingers to touch the terminals of plug 

when installing or removing from outlet.
Plug must be plugged into matching outlet that is properly installed 
and grounded in accordance with all local codes and ordinances. 
Do not modify plug provided. If it will not fit in outlet, have proper 
outlet installed by a qualified electrician.
Inspect tool cords periodically, and if damaged, have repaired by an 
authorized service facility.

INSTALLATION

3-Prong Plug

Grounding Prong

Properly Grounded Outlet

Figure 2 – 3-Prong Receptacle

Summary of Contents for 80177





















Reviews: