background image

www.lutron.com/support

Customer Assistance - 1.844.LUTRON1 (U.S.A./Canada) or +44.(0)20.7680.4481 (Europe)

P/N 041563 Rev. F 

11/2019

Configuration Instructions

Thermostat and Fan Coil  

Unit (FCU) Controller

English

 

The Palladiom thermostat and HVAC Controllers must be wired and configured as per the 

Palladiom QS Thermostat Install

 at www.lutron.com, then follow the instructions on this document.

Note:

 If an HVAC Controller will be connected directly to the thermostat, verify it has been installed and powered as per its instruction sheet, before proceeding to HVAC Controller Selection Mode. If no HVAC 

controller will be connected directly to the thermostat, skip all programming sections. This configuration will be completed by a certified Lutron dealer via the myRoom software.

Note:

 For SMC53 and SMC55 installation instructions, refer to www.lutron.com

Note:

 To run the FCU controller without the thermostat attached (detached mode) please follow instructions in the Lutron App Note #713 (P/N 048713) at www.lutron.com

A. HVAC Controller Selection Mode

(only available with thermostat version 4.12 or later)

 

1.  HVAC controller selection mode. 

The thermostat will automatically enter into HVAC controller selection mode if an HVAC controller has  

not been previously selected.

 

2.  Select the HVAC controller connected to the thermostat. 

Using the table below, press 

}

 or 

{

 buttons to select the correct HVAC  

controller being used and press 

u

.

 

3. Set the Modbus address.* 

Using the table above, press 

Set

 or 

Set

 to select the desired Modbus address and press 

u

.

    *    For more information, see the instructions included with the HVAC controller.

 

4.  Exit HVAC controller selection mode. 

When “End” is shown, press and hold 

u

 until the backlight flashes (3 seconds). The thermostat will  

proceed to the next relevant menu or to normal operation when finished.

 Note:

 "E1" will show on the display if the thermostat is not able to communicate with the HVAC controller.

B. Configuring the SMC53 / SMC55  (if  applicable)

 

1.  Enter basic configuration mode. 

If the Palladiom thermostat version 4.12 and later is being used in combination with 

SMC53 version 1013 and later or SMC55 version 5012 and later, then the thermostat will automatically enter  

the 

Basic Configuration Mode

 for an FCU controller being configured for the first time. 

 

   If the above is not true, then hold the °C | °F and   buttons for 3 seconds. Once the display begins to flash, release both buttons and  

immediately hold °C | °F for 3 seconds in order to enter the 

Basic Configuration Mode

.

 

2.  Set the Basic Configuration. 

Once in the 

Basic Configuration Mode

, tap the 

}

 or 

{

 buttons to display the desired configuration  

number as shown in the table to the below. Only the supported options are displayed.

 

3.  Save parameter values and exit basic configuration mode. 

Hold the 

u

 button for 3 seconds to save this configuration. The display will flash, then normal operation will begin.

 

4. Adjust advanced configuration parameters (optional). 

See the Advanced SMC Controller Configuration Instructions on next page.

  Re-enter Configuration Mode (optional)

 

 If any changes are needed after the configuration has been completed, follow the steps below.

 1.  

Cycle power to the thermostat. 

 2.

  Within 15 minutes of power cycling the unit, hold °C | °F and   buttons for 3 seconds. 

 3.

  Release the buttons and immediately hold: 

  

3a.

 

}

 for 

Controller Selection Mode

.

  

3b.

  °C | °F  for 

Basic Configuration Mode

.

  

3c.

     for 

Advanced Configuration Mode

.

  Determine Firmware Version (optional)

  

(only available with thermostat version 4.12 or later)

 1.  

To determine the 

Firmware Version of the thermostat

, hold 

}

 and 

{

 buttons for 3 seconds and the firmware version of the thermostat will be shown. 

 2.

  If thermostat is used in combination with SMC53 / SMC55 then within 10 seconds of completing step 1 either:

   2

a.

  Press the 

}

 button for the 

Firmware Version of the FCU Controller

.

   2

b.

  Press the °C | °F button for the 

Basic Configuration number of the FCU Controller

.

Parameter value

Set

Press to 

change  

parameter 

value

Press to select 

current value 

and proceed to 

next parameter

HVAC controller option

Modbus address

Va

lu

es b

as

ed o

 

H

VA

C

 c

o

ntr

o

lle

r

SMC53 / SMC55

01

01

Mitsubishi A1M

02

01-31  

(set by DIP switches 1-5)*

Cool Automation 

CoolPlug

03

99

LG PDRYCB500

04

01-08  

(set by DIP switches 1-4)*

Set

Set

Hold  °C | °F 

and   buttons 

for 3 seconds, 

then  °C | °F  for 

3 seconds to 

enter mode.

*    For Floating Point Valves, choose On / Off Relays, then see the Palladiom Thermostat and FCU Controller Configuration Instructions (P/N 041563) at www.lutron.com. Also, see Application Note #630 (P/N 048630) at www.lutron.com
**  Simultaneous 0 – 10 V

-

 and relay controls available in SMC55-HOSP version 5010 or later and SMC5500050407 version 5008 or later. 

Basic Configuration Table

System Configuration  

(Pipe Configuration)

Valve / Element  Control   

(Valve Type)

Fan Control  

(Fan Type)

2-pipe/Single Thermal Type 

(2-pipe mode)

Basic Configuration  Number

Basic Configuration Supported Models

SMC53x

SMC55x

As-Is

Use current configuration on the controller

00

•   4-pipe

•   2-pipe cooling with resistive 

heating element

Two  On / Off  relays*

H / M / L  Relays

01

0–10 V

Signal

02

Two 0–10 V

signals or one relay 

and one 0–10 V

-

H / M / L  Relays

03

0–10 V

Signal

04

•   2-pipe heating only

•   2-pipe cooling only

•   2-pipe with a changeover sensor

One  On / Off  relay*

H / M / L  Relays

Changeover Sensor

05

Heat-only

06

Cool-only

07

0–10 V

Signal

Changeover Sensor

08

Heat-only

09

Cool-only

10

One 0–10 V

signal

H / M / L  Relays

Changeover Sensor

11

Heat-only

12

Cool-only

13

0–10 V

Signal

Changeover Sensor

14

Heat-only

15

Cool-only

16

Summary of Contents for QS Room Thermostat

















Reviews: