Pall DU005-US Operator'S Manual Download

Page: 19 / 21

Document #: 4100022 Revision: F

Page #: 19 of 21

13. Pall

LifeSciences - SERVICE

The Magnetic Mixer system was developed exclusively for mixing fluids and solids into fluids in
specially designed disposable bags. Only use the Magnetic Mixer for these applications to
ensure a long service life.

Should your Magnetic Mixer require service, contact:

North America:

PALL Life Sciences
20 Walkup Drive
Westborough, MA 01581
E-mail: [email protected]

Europe:

PALL Life Sciences
Reugelstraat 2, B-3320 Hoegaarden, Belgium
Phone: +32 (0) 16.76.61.59
Fax: +32 (0) 16.76.76.25

Magnetic Mixer

Patents:
Pall.com/patents

14. SPARE PARTS

MM-DBBI002

Centering Aligner

MM-DBBI007

Magnetic Clamp

MM-DBBI008

Drive-Bag Interface

MM-DBBI004

O-Ring for use with Drive-Bag Interface

MM-LTOE059

M1 Latch Assembly

MM-LTOE060

M2 Latch Assembly

MM-LTOE061

Magnetic Mixer Rollers

2100024

Fuse

Summary of Contents for DU005-US






















Search results

Summary of Contents for DU005-US

Reviews:

Related manuals for DU005-US

Brands by name

Popular brands

Pall DU005-US, Operator'S Manual

Search results

Summary of Contents for DU005-US

Reviews:

Related manuals for DU005-US

Brands by name

Popular brands