Pakedge Device & Software C36-07 User Manual Download Page 40 | Manualshive

Page: 40 / 43

background image

C36

User Manual V1.2

TruStream™:

TruSteam does the inverse of SectorMaxx. If you require bandwidth and have enough

coverage, you can enable TruSteam to maximize your bandwidth.

Note:

Enabling both SectorMaxx and TruStream will produce results based on your environment. You may

get better coverage at certain times during the day and more bandwidth at other times. This setting is
only recommended for low-interference environments.

Fluxx™:

Fluxx helps reduce the power on APs based on interference. Fluxx will detect whether or not your

APs are interfering with one another and adjust power levels accordingly.

Contact Us

This section includes our technical support phone number and email address. You can also fill out the
support form and our technical support department will receive and respond to you ASAP.

«
...
38
39
40
41
42
...
»

Summary of Contents for C36-07












































Reviews:

No comments

Related manuals for C36-07

Brand: GE Pages: 2

Brand: XOXO Modular Pages: 13

Brand: Saitek Pages: 13

Brand: Balboa Water Group Pages: 28

Brand: UE Pages: 4

Brand: Samson Pages: 2

Brand: ICP DAS USA Pages: 4

Brand: ICP DAS USA Pages: 6

EIP-2000 Series

Brand: ICP DAS USA Pages: 19

Brand: L. G. B. Pages: 2

Brand: L-Acoustics Pages: 36

Frigolink FVB110B

Brand: WURM Pages: 4

Brand: Joy-it Pages: 7

Brand: Woodward Pages: 112

Brand: bluelab Pages: 39

Brand: SOMFY Pages: 2

Brand: Baby Trend Pages: 22

Brand: Barco Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands