background image

packardonline.com | 800.334.1769 3

Safety Considerations 

Safety 

Symbols 

The following definitions are used a safety considerations on EC Max and in 

this manual. Please read and observe all of these safety concerns. 

Installation and service of this motor should be attempted only by trained service 

technicians familiar with EC Max instructions and training manual.

EC Max is a multi-purpose replacement indoor blower motor. Proper wiring is 

critical to provide proper operation and maintain the proper operation of all safeties 

built into the HVAC system.

Always disconnect the main power from the unit being serviced before making any 

wiring connections to EC Max. It is also a good practice to confirm that the power 

is off with a meter.

EC Max is a multi-volt capable motor. Read all instructions and install the proper 

jumper for the line voltage before applying power to this motor.

Use of the wires provided in this kit is recommended. Should additional wires be 

needed, use equivalent size wire gauge and rated insulation. 

Improper installation, adjustment, alternation, service, maintenance, or use can 

cause explosion, fire, electrical shock, or other conditions which may cause 

personal injury, death, or property damage. Consult a qualified installer, service 

agency, or your distributor or branch for information or assistance. The qualified 

installer or agency must use the supplied or recommended parts when installing 

or servicing this product. 

                            

Warning indicates 

a hazardous situation which, if 

not avoided, could result in 

death or serious injury. 

Caution indicates 

a hazardous situation which, if not 

avoided, could result in minor or 

moderate injury.

This motor should be installed in accordance with accepted practices and 

installation instructions, and in compliance with all national and local codes. 

CAUTION

WARNING

CAUTION

WARNING

CAUTION

WARNING

CAUTION

WARNING

CAUTION

WARNING

CAUTION

WARNING

CAUTION

WARNING

Summary of Contents for 46001

















Reviews: