background image

NORTH AMERICAN SAFETY INSTRUCTIONS

USE AND APPLICATION

WARNING:

This floor sanding machine must be grounded.

This floor-sanding machine shall be grounded while in use to protect the operator from electric

shock. The machine is provided with a three-conductor cord and a moulded three-contact
grounding type attachment plug to fit the proper grounding type receptacle. The Green (or
Green and Yellow) conductor in the cord is the grounding wire. Never connect this wire to other
than the grounding pin of the attachment plug.

This floor-sanding machine is provided with an attachment plug as shown in sketch A. It is

intended for use on a nominal 120 volt circuit. If a properly grounded receptacle as shown in
sketch A is not available, an adaptor as shown in sketch 'C' should be installed as shown in sketch
B if the outlet box that houses the receptacle is grounded. Be sure to fasten the grounding tab with
a metal faceplate screw.

Floor sanding can result in an explosive mixture of fine dust and air. Use floor-sanding machine

only in a well-ventilated area free from any flame or match.

Moving Parts - to reduce the risk of injury, unplug the machine before replacing abrasive sheets

or carrying out any form of adjustment or servicing.

WARNING:

WARNING:

Risk of explosion.

Of potential injury.

This machine is intended for commercial use connected with the laying and maintaining of wooden floors and
decks.

These types of surfaces may be found both in commercial and household environments.

ATTACHMENT PLUG

SKETCH ‘C’

METAL

SCREW

COVER OF GROUNDED

OUTLET BOX SKETCH ‘B’

ADAPTER

GROUNDING

MEANS

COVER OF GROUNDED
OUTLET BOX SKETCH ‘A’

GROUNDING PIN

Manufactured in UK

© Hiretech

Summary of Contents for Wolverine PF7



















Reviews: