background image

6.

6.

IV. Installation Procedures

-SC8230S/W, SC8236S/W,SC8830BS/BW, SC8836BS/BW

Hood is designed for installation under a kitchen cabinet.

See Fig.1 for details.

1. Prepare duct location on hood .

7. Install electrical.

8. Install ductwork and seal with aluminum duct tape.

10. Reinstall bottom panel and reconnect lighting harness.

11. Slide oil cup into their opening on the bottom of the hood. Install protection 
      grilles over each blower opening and secure with the pre-installed screw.

9. Power up hood and check for leaks around duct tape and test all functions.

3. Reinforce cabinet bottom with wood strips
    if additional strengthening is required or if 
    cabinets are framed.

4. Remove

 

bottom panel from hood using a 

    Philips screwdriver to remove each of the 
    screws.  Also remove lighting harness by  
    pressing in on the clip to release the lights 
    from the internal wiring.

5. Use 4 wooden screws to secure the hood
    to the bottom of the cabinet.

6. Lift hood onto screws located on cabinet
    bottom and lock into place. Make sure all
    (4) key-holes cover the screws.  Tighten 
    each screw to secure hood to cabinet. 

2. Measure and cut out duct and electrical 
    openings in cabinet or wall to match up 
    with the hood. Make sure duct opening is 
    large enough to apply aluminum duct tape.

bottom panel & 

lighting harness

LED bottom panel 

& lighting harness

oil cup & 

protection grilles

duct tape

Fig 1

ductwork

electrical

wood blocking

installation screws

and key-holes

四.安裝步驟

-SC8230S/W, SC8236S/W,SC8830BS/BW, SC8836BS/BW  

 1.請準備安裝位置及空間

 2.測量出風口及電源線孔的大小

   後再鑽孔

 3.櫥櫃需加強本機固定的地方

建議

   使用木條強化在櫥櫃內底部

 4.請用十字螺絲起子移除油機底板

   

卸下油機底板及燈泡電線

 

5.依安裝位置設置四支木螺釘

 6.安裝時用木螺釘扣上之後

將油機

   與櫥櫃用螺絲鎖緊

讓油機與櫥櫃

   安全不會掉落

 7.裝設電源

 8.安裝風管並用風管膠帶密封

 9.檢查風管處是否緊密及其他功能是

   否正常

10.將油機底板與燈泡重新安裝上去

11.將油杯與出風口安全網裝進油機

櫥櫃安裝說明:(如圖一)

煙罩與燈源線 

油杯與保護網

圖一

電源線孔

木條

風管膠帶

木螺釘與鑰匙孔

風管圈孔

LED煙罩與燈源線 

Summary of Contents for SC8130BS



















Reviews: