SQUEEGEE ASSEMBLY
PART #608521
11
ITEM PART NO. DESCRIPTION
QTY.
1
960008
Bolt, Shoulder
2
2
609703
Wheel
2
3
608506
Squeegee Channel Weldment
1
4
920019
Nut, 1/4-20 Hex Jam
3
5
W189D
Screw, 14-20x3/4 HH CS
2
6
A13018
Knob
2
7
W506D
Screw,5/16-18x3/4 HH MS
6
8
W380D
Screw, 10-32x3/4 PHP
16
9
607209
Retainer-Squeegee Blade
2
10
600705
Blade, 28" Squeegee
2
11
600301
Arm Weldment-Squeegee
1
12
980006
Washer, 5/16 Lock
6
13
920001
Nut, 10-32 Elastic Stop
2
14
980007
Washer, 5/16 Flat
6
ITEM PART NO. DESCRIPTION
QTY.
15
960007
Bolt, Shoulder, 3/8x1/2 Lg
2
16
600806
Bracket, Arm Support
2
17
600205
Adaptor, Hose
1
18
604106
Hose, Vacuum
1
19
600206
Adaptor, Hose
1
20
920012
Nut, 5/16-18 ESNA Lock
4
21
962015
Screw, 10-32x3/8 Pan Hd
2
22
608507
Support, Lock Backup
1
23
605102
Lock, Squeegee Spring
1
24
608201
Spacer, Squeegee Support
2
25
608512
Stop, Squeegee Arm
1
26
W168D
Screw, Set
1
27
962010
Screw, 1/4-20x1 HHCS
1
For the Models PV-18S/Gulper 18PS which include the
Squeegee Assembly:
1.
Position the machine on a level surface.
2.
Unlock the lower squeegee lift arm weldment (11).
3.
Align the squeegee with the lift arm weldment; using the
shoulder screws (5) on the back side of the lift arm
weldment, place the jam nuts (4) between the arm weldment
and squeegee and then screw the knobs (6) on the front of
the squeegee assembly. Leave the hardware slightly loose.
4.
Position the squeegee assembly to assure that it sits flat
from side to side level with the surface. Then tighten the
knobs.
5.
Connect the vacuum hose assembly, Items 17, 18 and 19
to the tank adaptor and squeegee adaptor.
6.
Adjust the squeegee height by rotating the screw (27)
clockwise to lower the squeegee and counterclockwise to
raise the squeegee.
Squeegee Assembly as an Accessory - for the Models PV-
12/Gulper 12P, PV-18/Gulper 18P and PV-18D/Gulper
18PD:
1.
Remove the head assembly and the filter bag assembly.
2.
Turn the machine upside down.
3.
Mount the arm support brackets (16) to the inner surface
of the squeegee lift arm weldment (11) using the shoulder
screws (15), flat washers (14) and jam nut (20). Reference
the illustration - two washers are on the outside of the lift
arm weldment and one washer is between the support
bracket and squeegee lift arm weldment. Tighten the hard-
ware and check for free rotation. If needed, slightly loosen
the jam nut.
4.
Mount the squeegee arm stop (25) to the lift arm weldment
(11) using the set screw (26). Then assemble the screw
(27) and nut (4) to the stop (25) as illustrated.
5.
Position this assembly on the bottom of the tank with the
foot pedal to the rear of the tank, facing down.
6.
Attach the arm support brackets (16) and the spacers (24)
to the tank with the bolt (7) and washer (12).
7.
Assemble the lock backup support (22) to the lock spring
(23) with the screw (21) and nut (13) keeping the edges
flush.
8.
Attach the spring lock assembly (22&23) to the bottom of
the tank using the bolt (7) and washer (12).
9.
With the spring lock pressed in against the tank, check
that the pedal clears the spring lock. Loosen the bolt (7)
to adjust the spring lock assembly (22&23) location.
10. Turn the machine upright.
11. Proceed with steps 1-4 from the previous section.
12. If using on a PV-12/12P remove the adaptor (17) and cut
the hose assembly (18&19) to a 16 inch length. The 16
inches includes the adaptor (19). Do not cut the hose
assembly for the PV-18/18P and PV-18D/18PD.
13. Screw adaptor (17) onto the hose assembly.
14. Connect the vacuum hose assembly, Items 17, 18 and 19
to the tank adaptor and squeegee adaptor.
15. Adjust the squeegee height by rotating the screw (27)
clockwise to lower the squeegee and counterclockwise to
raise the squeegee.
16. Replace the head assembly and filter bag assembly.
MOUNTING INSTRUCTIONS
