Pacific Wave PW-FE1-4ETH User Manual Download Page 8

Page: 8 / 16

User Manual

PW-FE1-4Eth

E1-Ethernet Converter

www.pacificwave-wireless.com

Page 8 of 16

LOF: Alarm indicator lamp for input signal out-of-frame in E1 line.

Constantly lightening indicates the alarm with local device; flash
indicates the alarm with opposite device. Alarm status of opposite
device can be detected only at framing mode.

LOS: E1 link interruption alarm. Always lights after starting up till

synchronization is established. It also lights in case of E1 link
interruption or signal loss in communication.

AIS: Always lights after receiving a alarm indication signal.
LOOP: Always lights in testing if transmitting local loop, flickers if remote

E1 interface loop instructions or pseudo-random sequence test
instructions.

RAL : Always light when E1 line of remote site cut down

Summary of Contents for PW-FE1-4ETH

















Search results

Summary of Contents for PW-FE1-4ETH

Reviews:

Related manuals for PW-FE1-4ETH

Brands by name

Popular brands

Pacific Wave PW-FE1-4ETH, User Manual

Search results

Summary of Contents for PW-FE1-4ETH

Reviews:

Related manuals for PW-FE1-4ETH

Brands by name

Popular brands