background image

Page 19

For Pump technical questions, please call 1-888-866-5797. 

For Engine technical questions, please call 1-800-520-0882.

ITEM 69747 

        

SAFETY

O

PERA

TION

M

AINTENANCE

SETUP

Problem

Possible Causes

Probable Solutions

Engine stops 

suddenly

1.  Low oil shutdown. 

2.  Fuel tank empty or full of impure or low quality 

gasoline. 

 

3.  Defective fuel tank cap creating vacuum, 

preventing proper fuel flow.

4.  Faulty magneto.
5.  Disconnected or improperly 

connected spark plug cap.

1.  Fill engine oil to proper level.  Check 

engine oil before EVERY use.

2.  Fill fuel tank with fresh 87+ octane 

unleaded gasoline.

 

Do not use gasoline with more than 

10% ethanol (E15, E20, E85, etc.).

3.  Test/replace fuel tank cap. 

4.  Have qualified technician service magneto.
5.  Secure spark plug cap.

Engine stops when 

under heavy load

1.  Dirty air filter.
2.  Engine running cold.

1.  Clean or replace element.
2.  Allow engine to warm up prior 

to operating equipment.

Engine knocks

1.  Old or low quality gasoline. 

 

 

2.  Engine overloaded.
3.  Incorrect spark timing, deposit buildup, worn 

engine, or other mechanical problems.

1.  Fill fuel tank with fresh 87+ octane 

unleaded gasoline. 

  

Do not use gasoline with more than 

10% ethanol (E15, E20, E85, etc.).

2.  Do not exceed equipment’s load rating.
3.  Have qualified technician diagnose 

and service engine.

Engine backfires

1.  Impure or low quality gasoline. 

 

 

2.  Engine too cold. 

3.  Intake valve stuck or overheated engine. 

4.  Incorrect timing.

1.  Fill fuel tank with fresh 87+ octane 

unleaded gasoline. 

  

Do not use gasoline with more than 

10% ethanol (E15, E20, E85, etc.).

2.  Use cold weather fuel and oil 

additives to prevent backfiring.

3.  Have qualified technician diagnose 

and service engine.

4.  Check engine timing.

Follow all safety precautions whenever diagnosing or servicing the equipment or engine.

PLEASE READ THE FOLLOWING CAREFULLY

THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM 

IN THIS MANUAL AS A REFERENCE TOOL ONLY.  NEITHER THE MANUFACTURER OR DISTRIBUTOR 

MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS 

QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO REPLACE 

ANY PARTS OF THE PRODUCT.  IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY 

STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND 

LICENSED TECHNICIANS, AND NOT BY THE BUYER.  THE BUYER ASSUMES ALL RISK AND LIABILITY 

ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS 

THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.

Summary of Contents for 69747

























Reviews: