background image

18

SUPER-SD1

220206-20

Ash System - Leg model

Ash System - Pedestal model

1 .. Ash dump assembly

1 .. Ash dump assembly

1 .. Ash dump gasket

1 .. Ash dump gasket

1 .. Ash pan (Super 27 model)

1 .. Ash pan (Super 27 model)

or . Ash pan (Vista model)

or . Ash pan (Vista model)

or . Ash pan (Summit model)

or . Ash pan (Summit model)

Super 27 - Leg Model ....................... (SUPR.ASHLEG) ... (SUPD.ASHLEG)
Super 27 - Pedestal Model ............... (SUPR.ASHPED) .... (SUPD.ASHPED)
Vista - Leg Model ............................. (VIST.ASHLEG)
Vista - Pedestal Model...................... (VIST.ASHPED)
Summit - Pedestal Model ................. (SUMM.ASHPED)
Summit - Leg Model ......................... (SUMM.ASHLEG)

Ash System Assembly
Instructions

Contents:

Note: Ash dump assembly should be installed prior to leg kit or pedestal kit assembly

Required tools: two - 1/2" wrench or socket or one - 3/4" wrench or socket

and one - 3/8" wrench or socket, one - 7/16" wrench or socket

Remove crate ( all models )

1) Carefully remove wood top and supports.
2) Remove plastic cover.
3) Using 7/16" wrench, remove lag bolts that secure stove body to bottom pallet.
4) Place stove body carefully on its back.
5) Using two 1/2" wrenches or a 3/4" wrench, remove pallet retaining brackets from stove

bottom.

Assembly

1) With stove body laying on its back, remove the 1/4" x 1" Tek screw located at the top

left of the stove bottom.

2) Remove the ash system hole cover and gasket located under the stove. Discard cover

plate and gasket.

3) Place new gasket provided over existing studs.
4) Install ash dump system over gasket and secure with two 1/2" nuts previously removed.
5) Install the 1/4" Tek screw in the original hole and secure.

Summary of Contents for SUPER 27 SPECTRUM





















Reviews: