background image

PACE Sodr-X-Tractor Handpiece 

©2012 PACE Inc., Southern Pines, NC.  All Rights Reserved   

Page 11 of 11 

www.paceworldwide.com 

PACE Incorporated retains the right to make changes to specifications contained herein at 
any time, without notice.  Contact your local authorized PACE Distributor or PACE 
Incorporated to obtain the latest specifications.

 

 
The following are trademarks and/or service marks of PACE, Incorporated, MD, USA: 
 

INSTACAL

, FUMEFLO

, HEATWISE

, PACEWORLDWIDE

PERMAGROUND

, POWERPORT

, POWERMODULE

, TEMPWISE

, TIP-

BRITE

, AUTO-OFF

,

 

TEKLINK

, and INTELLIHEAT

 

 
The following are registered trademarks and/or service marks of PACE Incorporated, Annapolis 
Junction Maryland U.S.A.   
 

ARM-EVAC

®

, FLO-D-SODR

®

, MINIWAVE

®

, PACE

®

, SENSATEMP

®

, SNAP-

VAC

®

, SODRTEK

®

, SODR-X-TRACTOR

®

, THERMOFLO

®

, THERMOJET

®

THERMOTWEEZ

®

, VISIFILTER

®

, THERMO-DRIVE

®

, and TOOLNET

®

 
PACE products meet or exceed all applicable military and civilian EOS/ESD, temperature stability 
and other specifications including MIL STD 2000, ANSI/JSTD 001, IPC7711, and IPC A-610. 
 
Additional copies of this manual or other PACE literature may be obtained from: 
 
 

 

 

 

www.paceworldwide.com

 

 

 
 

PACE Incorporated

 

 

Pace Europe

 

255 Air Tool Drive 

 

11 Holdom Avenue 

Southern Pines,  

 

Bletchley, Milton Keynes, 

North Carolina, 28387   

United Kingdom, MK1 1QU 

Tel:  (877) 882-PACE   

Tel:  011 44 1908 277666 

Tel:  (910) 695-7223 

 

Fax: 011 44 1908 277777 

Fax: (910) 695-1594 

 

 

 

 

 

 

 

 

 

 

 

 

 

Summary of Contents for SX-100












Reviews: