Pace DC900X Installation Manual Download Page 13

13

DC900X INSTALLER’S MANUAL (501-3434310) RELEASE 30th Oct. 2009

PREPARING FOR HOME CONTENT SHARING AT CLIENT SET-TOPS

Enabling Home Content Sharing at client set-tops

You need to enable Home Content Sharing at each of the client set-tops. Instructions below relate to the UEI 
Universal remote control. The button names might be different on other types of remote control.

1.  Ensure the NAS and client set-top 3 are switched on and there is a picture on the TV that is attached client 

set-top 3. 

2.  Press the 

POWER

 button on the set-top’s remote control, then press the 

Menu

 button. 

3.  The PACE USER SETTINGS menu appears on the TV screen.

4.  Press the 

U

 or 

D

 button to highlight 

Home Content Sharing

, then press 

OK/Select

.

5.  Press the 

U

 or 

D

 button to highlight 

Enable

, then press 

OK/Select

.

6.  Press the 

L

 button to redisplay the PACE USER SETTINGS menu.

7.  Press the 

POWER

 button to remove the menu from the screen.

8.  Repeat the above seven steps for client set-tops 1 and 2. 

OK

Select

OK

Select

OK

Select

OK

Select

Home Content Sharing

   Enable

> Disable

PACE USER SETTINGS
TV Aspect Ratio

TV Display Capability

Auto Pillarbox

Closed Captions

Front Panel Settings

HDMI Settings

Home Content Sharing

Restore Defaults
Select[OK] Exit[POWER]

Home Content Sharing

> Enable

   Disable

Programming the remote control for Home Content Sharing

Program the remote control for each of the client set-tops to give one-touch access to HCS functions. 
Instructions below relate to the UEI Universal remote control.

Programming the B button - My Network

After you have programmed the 

B

 button, you can press it to display the 

My Network

 screen on the TV. This 

screen gives you access, from any location within the HCS system, to all of the recorded content.

1.  Press the 

CABLE

 button on the remote, then press and hold the 

SETUP

 button until the 

CABLE

 button 

blinks twice.

2.  Use the number buttons on the remote to enter the code 

994

. The 

CABLE

 button blinks twice.

3.  Press (do not hold) the 

SETUP

 button, then use the number buttons to enter the code 

00237

.

4.  Press the 

B

 button. The 

CABLE

 button blinks twice.

Programming the C button - Bulk Delete of titles within folders

After you have programmed the 

C

 button, you can use it, on the 

My Network

 screen, to delete several titles 

within a folder at the same time.

1.  Press the 

CABLE

 button on the remote, then press and hold the 

SETUP

 button until the 

CABLE

 button 

blinks twice.

2.  Use the number buttons on the remote to enter the code 

994

. The 

CABLE

 button blinks twice.

3.  Press (do not hold) the 

SETUP

 button, then use the number buttons to enter the code 

00114

.

4.  Press the 

C

 button. The 

CABLE

 button blinks twice.

Summary of Contents for DC900X
























Reviews: