Pacific Accessory Corporation
Page 8
© 2019 AAMP Global. All rights reserved. PAC is a Power Brand of AAMP Global.
PAC-audio.com
Email - [email protected] - Phone: 727-592-5991
Complete Radio Replacement Kit with Integrated Climate
Control Retention for 2010-2015 Chevrolet Camaro
RPK5-GM4102
Rev: R6
Date: 010419
Picture of the BCM which is located under the driver side of the
dash just above the steering column
Close up of the Light Blue
connector located at the BCM
PAC HVAC Control Panel Testing and Verification
1. Turn the ignition on. The LCD at the top of the kit should come on and display the external temperature.
2. Verify functionality of the lock, unlock and hazard buttons.
3. Verify functionality of the rotary dials and all of the push buttons on each of HVAC knobs.
4.
For double DIN applications equipped with a 7” screen, verify that the face of the radio does not come in contact with the kit when ejecting a
disk. If it does you will need to adjust placement of the double DIN radio in the mounting brackets.
5. Verify the LED backlights dim when using the factory dimmer control.
6. Verify that the kit, including the temperature LCD, shuts off when the key is turned to the off position.
Product Updates (Firmware)
The interface can be updated with new firmware as it becomes available using the PAC-UP interface updater (sold separately). Please visit
www.
PAC-audio.com/firmware
for available updates.
The HVAC board can also be updated with new firmware using the RadioPRO application found at the same website link above.
Installation of the PAC HVAC control panel (cont.)
Vehicles equipped with MyLink radio
1. Connect the RPK5-GM4101-KIT-HAR to the vehicles white 20-pin connector that was originally connected to the factory Radio control panel.
2.
Connect the 8-pin Black Micro-fit Molex connector to the circuit board mounted to the back side of the PAC HVAC control module.
3. Locate the Orange / Black (Pin 15) and Pink / Black (Pin 19) wires in the 27-Pin Lt. Blue connector at the Body Control Module (BCM). The
BCM is located under the driver side of the dash.
4. Connect the loose end of the Orange / Black extension wire to the Orange / Black wire in Pin 15.
5. Connect the loose end of the Pink / Black extension wire to the Pink / Black wire in Pin 19.
6. Route both of the extension wires to the right and through the same opening that the White 20-pin connector passes through and connect
them to the bullet connectors on the RPK5-GM4101-KIT-HAR. Be sure to not route these wires near any moving parts as it could cause
damage to these wires in the event they become pinched.
** If the kit mounted door lock buttons operate in reverse after connection of these wires, then the Orange / Black wire and Pink / Black have
been connected in reverse. To fix, reverse the connections at the wires or simply swap the wires at the bullet connectors**
7. Fit the PAC HVAC control panel into the vehicle opening and secure at the bottom using the factory mounting hardware.
8. Assemble the remaining pieces of the dash.
Interface Testing and Verification
1. Turn the ignition on. The LED on the interface will turn on and the +12v accessory wire will turn on.
2. Turn on the radio and check balance and fade.
3.
Verify that all SWC are functioning properly for both the aftermarket radio and OnStar. To adjust OnStar volume, press the OnStar button
on the mirror then use the volume buttons on the SWC to adjust the level. The volume will raise a total of 8 times before returning to the
original level.
4. Pressing the OnStar button on the rearview mirror will turn off the rear speakers and allow the OnStar audio to be heard in the two front
speakers. The OnStar active LED will also turn on. When OnStar disconnects, the radio will un-mute or turn back on and the OnStar LED
will turn off. Pressing the Mute/OnStar button on the steering wheel for 1.5 seconds will also activate Onstar.
5. Turn off vehicle and remove key. RAP will be active and keep the radio on for 10 minutes, or until the driver’s door is opened.
6. The Accessory LED and radio will turn off when RAP turns off or the driver’s door is opened.