background image

10

Maximum exhaust gas temperature hysteresis [Fh20]

– this parameter describes

how much exhaust gas temperature should drop in relation to maximum temperature

for the controller to stop [Hot ] alarm and resume normal work.

6.7. Fuel shortage testing.

If central heating installation is equipped with exhaust gas temperature sensor

(

[Fc 1]

), then fuel shortage testing starts when exhaust gas temperature falls below

temperature set with additional thermostat knob. If there is no exhaust gas

temperature sensor (

[Fc 0]

), then fuel shortage testing starts when boiler water

temperature falls below value of

[L 65]

. If temperature tested during fuel shortage

testing stays below threshold for specified time, the controller will stop regulation

process and will show

[FUEL]

message on the display. This alarm can be erased with

STOP button.

Fuel shortage testing time during boiler start [Fd60]

– time set with this parameter

is used when testing fuel shortage during boiler start. Boiler is considered starting from

the time when the controller is switched from STOP mode to WORK mode and ends

when boiler temperature reaches minimum temperature (set with

[L 65]

parameter).

Setting

[Fd60]

parameter to „--” disables fuel shortage checking during boiler start.

Fuel shortage testing time in work mode [Fb30]

– time set with this parameter is

used when testing fuel shortage after boiler has started. Setting this parameter to „--”

disables fuel shortage checking in WORK mode.

6.8. Additional output.

Additional output work mode [Ar 0]

- the controller is equipped with a multipurpose

output that can work in one of following modes:

-

[Ar 0] mode

- output may control oil or gas boiler if such boiler exists in the

heating circuit. After switching the controller on with the main power switch, the

additional boiler is turned off and it turnes on again when there is no fuel in the solid

fuel boiler. This function is useful in heating systems where the solid fuel boiler is used

to cut heating costs. After erasing no fuel alarm by pressing STOP button, the

additional boiler is again turned off and the controller works again.

-

[Ar 1] mode

- output may control additional alarm signaling system. Boiler

temperature sensor malfunction, overheating or no fuel alarm will turn on the

additional alarm.

-

[Ar 2] mode

- output may control boiler emergency cooling system (e.g. pump).

In this mode the additional output is turned on in case of boiler overheating or boiler

temperature sensor error alarm.

-

[Ar 3] mode

- output may control devices working together with blow-in fan.

CAUTION.

Equipment should be connected to additional output using UM-1module.

Connection schemes are shown on picture 3.

Summary of Contents for RK-2001AT2

















Reviews: