background image

DESCRIPTION OF SYMBOLS

CARING FOR THE ENVIRONMENT

Power tools that are no longer usable should not be disposed of 

with household waste but in an environmentally friendly way. Please 

recycle where facilities exist. Check with your local council authority 

for recycling advice.

Recycling packaging reduces the need for landfill and raw materials. 

Reuse of recycled material decreases pollution in the environment. 

Please recycle packaging where facilities exist. Check with your 

local council authority for recycling advice.

Limited spare parts are available subject to availability. Please 

contact your local Bunnings Special Orders Desk to order the 

required spare parts.

For further information, or any parts not listed here,  
visit www.ozito.com.au or contact Ozito Customer Service: 
Australia 1800 069 486 
New Zealand 0508 069 486 
E-mail: [email protected]

SPARE PARTS

  

V

 

Volts

    

Hz

  

~

 

Alternating current

  

W

/min

 

Revolutions or 

 

reciprocation per minute

 

Regulator compliance mark

 

 

      

n

Warning

Wear hearing protection

Read instruction manual

5124

Wear eye protection

Wear a breathing mask

Important. Risk of injury!

 Do not reach into the running saw blade

Hertz

Watts

No load speed

Summary of Contents for SSB-407









Reviews: