Ozito RTS-002 Instruction Manual Download

Page: 2 / 8

ONLINE MANUAL

Scan this QR Code with your

mobile device to take you to

the online manual.

1  Collet Nut
2  Shaft Collar
3  Spindle Lock Button
4  Accessible Brushes

5  On/off Switch
6  Variable Speed Dial
7  Hanging Ring

ROTARY TOOL

KNOW YOUR PRODUCT

1. CHANGING ACCESSORIES

1. Press and hold the spindle

lock button.

8 Blade Sharpening

Attachment

9 Grinding Stone (Blade

Sharpening) x 1

10 Chainsaw Sharpening

Attachment

11 Diamond Sharpening Wheel

(Chainsaw Sharpening) x 3

12 Wrench

ACCESSORIES

SETUP & PREPARATION

2. Unscrew the collet nut.

Remove completely.

3. Select a suitable collet for

the accessory to be used

and insert. Then cover with

collet nut.

4. Insert shaft of

accessory into the

collet.

5. Tighten collet nut

using spindle lock and

spanner.

4. Slightly hand tighten the

collet nut so that it stays in

place.

WARNING:

ENSURE THE TOOL IS SWITCHED

OFF AND DISCONNECTED FROM THE POWER

SUPPLY BEFORE PERFORMING ANY OF THE

FOLLOWING STEPS.

Summary of Contents for RTS-002









Search results

Summary of Contents for RTS-002

Reviews:

Related manuals for RTS-002

Brands by name

Popular brands

Ozito RTS-002, Instruction Manual

Search results

Summary of Contents for RTS-002

Reviews:

Related manuals for RTS-002

Brands by name

Popular brands