background image

MAINTENANCE

DESCRIPTION OF SYMBOLS

Cleaning

1.  We recommend that you clean the appliance immediately after 

you use it.

2.  Keep the safety devices free of dirt and dust as much as 

possible. Wipe the equipment with a clean cloth.

3.  Clean the appliance regularly with a damp cloth and some soft 

soap. Do not use cleaning agents or solvents; these may be 

aggressive to the plastic parts in the appliance. Ensure that no 

water can get into the interior of the appliance.

Gear Box Grease Replenishment

WARNING! 

WEAR GLOVES WHEN HANDLING GREASE.

The grease in the gearbox will require replenishment after 

approximately 50 hours accumulative use. After this time, add 

approximately 50 grams (approximately 2 – 3 teaspoons) of the 

grease (supplied), into the gearbox. 

First remove the grease cap from the 

drill by using the pin spanner. Once 

removed, add the grease through this 

hole. Ensure the grease cap is secured 

back into position prior to operation. If 

additional grease is required, please 

contact Ozito Customer Service.

Storage

Pull the mains plug out of the socket, switch off the tool and make 

sure that it is secured in such a way that it cannot be started up 

again by any unauthorised person. Store the tool in a dry location 

which is not accessible to unauthorised persons.

Supply Cords

If replacement of the supply cord is necessary, this has to be done 

by a certified electrician in order to avoid a safety hazard.

Note: 

Ozito Industries will not be responsible for any damage or 

injuries caused by the repair of the tool by an unauthorised person 

or by mishandling of the tool.

WARNING! 

BEFORE CLEANING THE APPLIANCE OR 

CARRYING OUT ANY MAINTENANCE PROCEDURE, 

MAKE SURE THAT IT IS DISCONNECTED FROM THE 

POWER SUPPLY TO PREVENT ACCIDENTAL STARTING.

Millimetre

Warning

Regulatory Compliance Mark

(RCM)

Double insulated

Wear eye, ear & breathing 

protection

V

Volts

Hz

W

Hertz

~

bpm

J

mm

Alternating Current

Watts

beats per minute

Joules

Read Instruction Manual

Power tools that are no longer usable should not 

be disposed of with household waste but in an 

environmentally friendly way. Please recycle where 

facilities exist. Check with your local council authority for 

recycling advice.

Recycling packaging reduces the need for landfill and raw 

materials. Reuse of recycled material decreases pollution 

in the environment. Please recycle packaging where 

facilities exist. Check with your local council authority for 

recycling advice.

CARING FOR THE ENVIRONMENT

SPARE PARTS

Spare parts can be ordered from the Special Orders Desk at your 

local Bunnings Warehouse. 
For further information, or any parts not listed here, visit  
www.ozito.com.au or contact Ozito Customer Service: 
Australia 1800 069 486 
New Zealand 0508 069 486 
E-mail: [email protected]

1500W

ROTARY

HAMMER

3

Summary of Contents for RHD-1550







Reviews: