DESCRIPTION OF SYMBOLS
TROUBLESHOOTING
Removing and Fitting the Blade
Cleaning, Maintenance and Storage
1. To remove the blade screw, hold the blade firmly and
with a 13mm socket loosen the blade screw by turning
it anti-clockwise.
NOTE:
A piece of timber will assist in holding the blade
while removing or tightening the blade bolt.
2. Remove the blade screw, washer and blade.
3. To fit the blade, place the blade over the centre hole aligning the lugs.
4. Then retighten the fastening screw with the universal wrench. The tightening torque should be
approx. 25 Nm.
TIMBER
• Keep all nuts, bolts and screws tight to be sure the lawn mower is in a safe working condition.
• Check the catcher frequently for wear or deterioration.
• Replace worn or damaged parts for safety.
• Only use the replacement blade and blade bolt specified for this product.
• Be careful during adjustments of the lawn mower to prevent entrapment of the fingers between
moving blade and fixed parts of the machine.
• When not in use, the mower should be stored in a dry, frost-free location, out of reach of
children. If the housing of the mower requires cleaning, do not use solvents but a moist soft
cloth and brush only.
• Frequently check the wheel threads are firm and tight.
Note: Ozito Industries will not be responsible for any damage or injuries caused by the repair of the
lawn mower by an unauthorised person or by mishandling of the lawn mower. This tool is designed
for DIY use - use in commercial or industrial environments will void the warranty.
WARNING!
ALWAYS ENSURE THE LAWN MOWER
BLADE HAS COMPLETELY STOPPED, REMOVE
SAFETY KEY, BATTERY AND GRASS CATCHER PRIOR
TO ANY MAINTENANCE.
CAUTION!
ALWAYS USE GLOVES WHEN HANDLING
THE BLADE. SHARP EDGES COULD CAUSE INJURY.
Problem Cause
Remedy
Mower is not
starting
Possible clogging
Check underneath the mower and clear out
as necessary
Battery is low in charge
Charge battery
Battery not inserted
properly
Insert battery pack correctly
Grass too long
Raise the cutting height to reduce starting
load
Safety key not inserted
correctly
Fit correctly
Mower is
hard to push
Height of cut too low
Raise cutting height
Cutting blade blunt
Replace blade
Possible clogging
Check underneath the mower and clear out
as necessary
Grass too long
Raise the cutting height and walk slower
Grass too dense
Raise the cutting height and walk slower and
cut more frequently
Wet grass
Wait until the grass dries before mowing
Motor stops
while cutting
Height of cut too low
Raise the cutting height
Battery has no power
Charge battery
Mower is
not catching
grass properly
Height of cut too low
Raise the cutting height
Wet grass
Wait until the grass dries before mowing
Mower
vibrating
Bent or damaged blade
Replace blade
Replace the metal blade after 50 hours mowing or 2 years whichever
is sooner. If the blade is cracked or damaged replace it with a new
one.
MAINTENANCE
Dispose of batteries correctly
Guaranteed sound power level: 96 dB
Keep your distance
Read the directions for use before operating the equipment.
Caution: Sharp blades! Pull out the safety plug before carrying
out any repair work or if the power cable is damaged.
The blades will continue to rotate after the motor is switched off.
Safety class II
Protect the equipment from
rain and damp conditions
96
Declaration of Conformity
Gao/Product-Management
Weichselgartner/General-Manager
explains the following conformity according to EU directives and norms for
the following product
Cordless Lawn Mower PXCLMK-218U / Eco Charger PXCG-120U (Ozito)
2014/29/EU
2005/32/EC_2009/125/EC
2014/35/EU
2006/28/EC
X
2014/30/EU
2014/32/EU
2014/53/EC
2014/68/EU
90/396/EC_2009/142/EC
89/686/EC_96/58/EC
X
2011/65/EU
X
2006/42/EC
Annex IV
Notified Body:
Notified Body No.:
Reg. No.:
X
2000/14/EC_2005/88/EC
Annex V
X
Annex VI
Noise: measured L
WA
= 92,05 dB (A); guaranteed L
WA
= 96 dB (A)
P = KW; L/Ø = 33 cm
Notified Body: SNCH (NB0499)
2012/46/EU
Emission No.:
Standard references: EN 60335-1; EN 60335-2-29; EN 60335-2-77; EN 62233;
EN 55014-1; EN 55014-2; EN 61000-3-2; EN 61000-3-3
Landau/Isar, den 01.08.2017
First CE: 17
Archive-File/Record:
NAPR017426
Art.-No.:
30.001.87
I.-No.: 11017
Documents registrar:
R. Gehard
Subject to change without notice
Wiesenweg 22, D-94405 Landau/Isar
ISC GmbH · Eschenstraße 6 · D-94405 Landau/Isar
3000187_11017_PXCLMK_218EU.indd 135
05.09.2017 13:08:02
Only replace the blade with a genuine Ozito replacement blade, as this will ensure top performance
and safety under all conditions.
Battery protection system
The tool is equipped with the battery protection system, which helps to ensure a long
service life.
The output power automatically cuts off during operation when the tool and/or battery
are placed under the following situations:
• When the tool is overloaded:
If this occurs, release the start/stop lever safety key and batteries and remove
causes of overload, then reinsert the safety key and batteries, then press and hold
the lock-off button and pull the start stop lever again to restart.
• When the remaining battery capacity becomes low:
Recharge the battery packs.
Note:
The indicated capacity may be lower than the actual level during use or
immediately after using the tool.
Note:
Always use 2 batteries of same capacity and same charge state with the
mower.
