background image

3.  MOWING

OPERATION

1.   Press and hold the lock-off 

button.

3.   Release the start/stop lever 

to stop the mower.

To prevent accidental start up, the mower is fitted with a dual action switch.

1.   Open the battery cover. Press the 

battery release tab and remove 

the battery.

2.   Pull the start/stop lever 

towards the handle to start 

the mower and then release 

the lock-off button.

2.   Close the battery cover.

Switching On and Off

Removing the Batteries from the Mower

PXBSDMS-0182

•   While using your lawn mower always wear substantial closed, heavy 

footwear and long trousers.

•   Make sure the lawn is clear of sticks, stones, wire and debris; they could 

be thrown by the blade.

•   Before using the lawn mower and after any impact, check for signs of 

wear or damage and repair as necessary.

•   Replace a worn or damaged blade together with the blade bolt to 

preserve balance.

IMPORTANT! 

DO NOT MOW IN POOR VISIBILITY 

CONDITIONS, IN THE RAIN OR WHEN GRASS IS 
WET.

 Start mowing the edge of the 

lawn and work along making 

sure to overlap each pass by a 

few centimetres.

When mowing long grass be sure to not overload the motor.  First cut with the 

highest cutting 

height and then 

to the desired 

height. This will 

help reduce the 

load.

Lawn Mowing Tips 

WARNING!

 

NEVER LEAVE THE BATTERIES INSIDE 

THE MOWER, WHEN MOWER IS NOT IN USE.

Audible Warning

The mower is equipped with an audible warning system, which helps to 

ensure a log service life and improved user experience.

  Low Battery:

When the lawn mower batteries are running low, the mower will continuously 

beep. If this occurs, either charge the current batteries or replace with fully 

charged batteries.

  Overload Protection:

When the lawn mower motor is overloaded, short warning beeps will warn 

the user and the mower will stop. Release the start/stop lever, remove safety 

key, batteries and investigate the cause of the overload. Possible causes if 

this occurs,
Height of cut too low - Adjust the cutting height to a higher setting. 

Possible clogging - Check underneath the mower and clear out as necessary. 

Wet grass - Wait until the grass dries before mowing. 

Grass too dense - Raise the cutting height and walk slower.

Summary of Contents for Power X Change PXBSDMS-0182











Reviews: