manualshive.com logo in svg

Ozito PFFP-65E, Instruction Manual

Share
Download
Ozito PFFP-65E Instruction Manual Download Page 5

1

PFFP-65E

  7.  STARTING & STOPPING ENGINE

  6. PRE-OPERATION INSPECTION

1.   Move the choke 

to the left (closed 

position) and the 

fuel lever to the right 

(open position).

1.   Decrease the speed 

of the engine by 

moving the throttle 

to the left 

 and 

allow to idle for 10-20 

seconds.

2.   Move the throttle lever 

to the right 

 (fast 

position).

2.   Move the fuel lever to the 

left (closed position).

Note: 

 Allow the engine to cool 

down before moving or 

storing the pump.

4.   Once started move the 

choke lever to the right 

(open position) and the 

throttle lever to the left 

 (slow position) and 

allow to idle for 3 minutes.

3.   Grip the recoil starter 

and slowly pull until 

resistance is felt, 

then pull the recoil 

starter rapidly. 

Allow the rope to 

rewind slowly and 

if necessary, repeat 

this procedure until 

the engine starts.

Air Filter

Starting the Engine

Stopping the Engine

Spark Plugs

1.   Ensure the filter 

is free from any 

debris.

2.   If necessary clean or replace the filter by following the steps 

outlined in the maintenance section of this manual.

2.   To remove and install the spark plug refer to the 

maintenance section of this manual.

1.   Make sure the electrode 

is clean and the air gap 

is correct (refer to the 

specs of the spark plug 

manufacture).

The air filter must always be in perfect working order, to 

prevent debris and dust from being sucked into the engine thus 

reducing the efficiency and life of the machine.

Use only the spark plugs that are recommended for this petrol 

pump: Champion RC12YC. 

Note:  

Using a spark plug other than that specified could lead to 

serious engine damage.

Summary of Contents for PFFP-65E









Reviews:

No comments

Brands by name

Popular brands

Load more brands