background image

WARRANTY

THIS WARRANTY FORM AND CONFIRMED BUNNINGS REGISTER RECEIPT SHOULD
BE

RETAINED BY THE CUSTOMER

AT ALL TIMES

The warranty is only made available by returning the product to your nearest
Bunnings Building Supplies with a 

confirmed Bunnings register receipt.

PURCHASED FROM: ________________________________________________

DATE PURCHASED: ________________________________________________

3 YEAR REPLACEMENT WARRANTY

Your Ozito tool is guaranteed for a period of 

36 months from the original date of

purchase

and is intended for DIY (Do it yourself) use only.

WARNING

The following actions will result in the warranty being void.

Professional, Industrial or high frequency use.

If the tool has been operated on a supply voltage other than that specified on
the tool.

If the tool shows signs of damage or defects caused by or resulting from abuse,
accidents or alterations.

If the tool is disassembled or tampered with in any way.

Note:

Warranty excludes consumable parts such as brushes, batteries, sanding
pads, blades, discs, drill bits, collets and router bits.

YOUR WARRANTY FORM SHOULD BE RETAINED

BY YOU AT ALL TIMES.

SHOULD YOU HAVE ANY QUESTIONS PRIOR TO

RETURNING YOUR PRODUCT FOR WARRANTY OR

REPAIR PLEASE TELEPHONE OUR CUSTOMER

SERVICE HELPLINE:

Australia 1800 069 486

New Zealand 0508 069 486

TO ENSURE A SPEEDY RESPONSE PLEASE HAVE THE MODEL NUMBER

AND DATE OF PURCHASE AVAILABLE. AN OZITO CUSTOMER SERVICE

REPRESENTATIVE WILL TAKE YOUR CALL AND ANSWER ANY QUESTIONS

YOU MAY HAVE RELATING TO THE WARRANTY POLICY OR PROCEDURE.

Summary of Contents for OZCD12V1A













Reviews: