Ozito IGP-2018, Instruction Manual

Page: 6 / 24

4. OUTLETS 5. TROUBLESHOOTING
AC Appliances
Check the total rating of the appliance to be connected and ensure
the rating of the appliance(s) does not exceed the rating of the
generator.
1. Start the generator and ensure
the AC power indicator lights up.
Allow the engine to stabilise before
connecting appliances.
2. Check that the appliance
and the AC power switch are
switched off.
3. Plug the appliance into
either of the AC sockets.
4. Flip the AC power switch
to the on position and then
you can start using the
equipment.
Note:
If the connected appliance does not operate, refer to the
‘
Overload Indicator (RED)
’ and ‘
Inrush Current Overload
’
sections for troubleshooting.
USB Output
The generator has 2 USB outlets that supply 1.0A and 2.1A
respectively. These are always on once the generator is started.
Connect the device to be
charged/powered via a USB
cable (not supplied) to the USB
port.
Note: The USB outlets provides
power only, it does not
provide any communication
capabilities. A suitable USB
cable must be used (not included).
Maintenance
Refer to the Maintenance Manual for maintenance instructions.
The instructions should be followed to ensure optimum operation.
2000W
PETROL INVERTER GENERATOR
4 STROKE 119CC ENGINE
2000W
INVERTER
TECHNOLOGY
2x
AC SOCKET 1
USB PORTS
AC SOCKET 2
OVERLOAD
AC OUTPUT
AC
IF OVERLOADED
RESTART ENGINE TO RESET
AC POWER
I
0
I
0
I
0
240V
1
240V
2
FUEL ECONOMY
ENGINE POWER
AUTOMATIC ENGINE SHUT OFF
REFILL MOTOR OIL
LOW OIL
OFF ON
OFF ON
OFF ON
LOW OIL
2000W
PETROL INVERTER GENERATOR
4 STROKE 119CC ENGINE
2000W
INVERTER
TECHNOLOGY
2x
AC SOCKET 1
USB PORTS
AC SOCKET 2
OVERLOAD
AC OUTPUT
AC
IF OVERLOADED
RESTART ENGINE TO RESET
AC POWER
0
I
0
I
0
I
240V
1
240V
2
FUEL ECONOMY
ENGINE POWER
AUTOMATIC ENGINE SHUT OFF
REFILL MOTOR OIL
LOW OIL
OFF ON
OFF ON
OFF ON
LOW OIL
2000W
PETROL INVERTER GENERATOR
4 STROKE 119CC ENGINE
2000W
INVERTER
TECHNOLOGY AC SOCKET 1 AC SOCKET 2
OVERLOAD
AC OUTPUT
AC
IF OVERLOADED
RESTART ENGINE TO RESET
AC POWER
I
0
0
I
0
I
240V
1
240V
2
FUEL ECONOMY
ENGINE POWER
AUTOMATIC ENGINE SHUT OFF
REFILL MOTOR OIL
LOW OIL
OFF ON
OFF ON
OFF ON
LOW OIL
1.0A
USB PORTS
2.1A
2000W
PETROL INVERTER GENERATOR
4 STROKE 119CC ENGINE
2000W
INVERTER
TECHNOLOGY
2x
AC SOCKET 1
USB PORTS
AC SOCKET 2
OVERLOAD
AC OUTPUT
AC
IF OVERLOADED
RESTART ENGINE TO RESET
AC POWER
I 0
0
I
I
0
240V
1
240V
2
FUEL ECONOMY
ENGINE POWER
AUTOMATIC ENGINE SHUT OFF
REFILL MOTOR OIL
LOW OIL
OFF ON
OFF ON
OFF ON
LOW OIL
WARNING! BEFORE CONNECTING, INSPECT THE
APPLIANCE CABLES. DO NOT USE THE APPLIANCE IF
THERE ARE SIGNS OF FRAYING AND/OR DAMAGE.
WARNING! NEVER ADD MORE LOAD THAN THE
GENERATOR CAPACITY. TAKE CARE TO CONSIDER
SURGE LOADS IN GENERATOR CAPACITY.
WARNING! DO NOT USE THE OUTLET IF THE COVERS
ARE BROKEN.
Problem Possible Cause Solution
Engine
• will not start,
• shuts down
after starting
or
• starts but
runs rough
Choke is in off
position.
Move choke to on position.
No fuel.
Add unleaded 91 RON petrol
to fuel tank.
Engine switch is
in the off position. Set engine switch to on.
Oil is low.
Check oil level and fill if
necessary.
Spark plug
connector is
not properly
connected.
Check and reattach
connector if necessary.
Spark plug is
faulty.
Replace spark plug.
Fuel is stale/old,
or there is water
in the fuel.
Drain system of all fuel and
refill with fresh unleaded 91
RON petrol.
Engine is flooded. Wait 5 minutes before
restarting engine.
Engine stored
without treating
or draining fuel.
Bad fuel is used.
Drain system of all fuel and
refill with fresh unleaded 91
RON petrol.
Air filter is dirty.
Check air filter. Clean if
necessary.
Fuel filter is dirty. Check fuel filter. Clean if
necessary.
Engine lacks
power
Engine stored
without treating
or draining fuel.
Bad fuel is used.
Drain system of all fuel and
refill with fresh unleaded 91
RON petrol.
Air filter is dirty.
Check air filter. Clean if
necessary.
No power
Device plugged
in is faulty.
Check device for damage,
try plugging in a different
device.
Generator is
overloaded.
Refer to overload indicator
section.
Poor connection
or defective
cable.
Check for damage and
replace if necessary.