Ozito Industries will not be responsible for any damage or injuries
caused by repair of the tool by an unauthorised person or mishandling
or mistreatment of the tool. This tool is designed for Domestic Home Use
only. Use in commercial or industrial environments will void the warranty.
CAUTION!:
ALWAYS HANDLE THE BLADE WITH CARE
– SHARP EDGES COULD CAUSE SERIOUS INJURY.
USE GLOVES.
CARING FOR THE ENVIRONMENT
Tools that are no longer usable should not be disposed of with
household waste but in an environmentally friendly way. Please
recycle where facilities exist. Check with your local council
authority for recycling advice.
Recycling packaging reduces the need for landfill and raw
materials. Reuse of recycled material decreases pollution in the
environment. Please recycle packaging where facilities exist.
Check with your local council authority for recycling advice.
Switch Box Assy.
SPELM1000-06
Belt
SPELM1000-30
Blade & Bolt
SPELM1000-33
Blade
Bolt SPELM1000-35
Tension Spring
SPELM1000-40
Spare parts can be ordered from the Special Orders Desk
at your local Bunnings Warehouse.
For further information, or any parts not listed here, visit
www.ozito.com.au or contact Ozito customer service
Australia 1800 069 486
New Zealand 0508 069 486
E-mail: [email protected]
SPARE PARTS
MAINTENANCE
WARNING!:
BEFORE CLEANING YOUR ECOMOW
ELECTRIC MOWER OR CARRYING OUT ANY
MAINTENANCE PROCEDURE, MAKE SURE THAT THE
MOTOR IS OFF AND THE TOOL DISCONNECTED FROM
THE POWER SUPPLY TO PREVENT ACCIDENTAL
STARTING.
Removing the Blade
1.
To remove the blade bolt, hold the blade
firmly and with a 13mm spanner (not
supplied) loosen the blade bolt by turning it
anti-clockwise.
2.
Remove the blade bolt, and blade.
3. Inspect for damage and clean as necessary.
Renew the metal blade after 50 hours mowing or 2 years whichever is
the sooner – regardless of condition. If the blade is cracked or damaged
replace it with a new one. Never use a blade bolt if the insulated head is
damaged, cracked or missing.
1. Fit the blade to the fan with the tilt edges of the blade facing towards the
mower, ensuring the blade is located onto the fan location points correctly.
2. Re-assemble blade bolt through blade and fan.
3.
Hold the fan firmly and tighten blade bolt with a 13mm spanner, by turning in
a clockwise direction. Do not over tighten.
Fitting the Blade
•
Keep all nuts, bolts and screws tight to be sure the lawn mower is in a safe
working condition.
• Check the catcher frequently for wear or deterioration.
• Replace worn or damaged parts for safety.
•
Only use the replacement blade, blade bolt, and impeller specified for this
product.
• Be careful during adjustments of the lawn mower to prevent entrapment of
the fingers between moving blade and fixed parts of the machine.
• Oil the wheel pins.
•
When not in use, the mower should be stored in a dry, frost-free location, out
of reach of children.If the housing of the mower requires cleaning, do not use
solvents but a moist soft cloth and brush only.
•
Frequently check the wheel threads are firm and tight.
V
Volts
Hz
~
Alternating current
W
/min
Revolutions or
reciprocation per minute
n
o
Warning
Regulator compliance mark
Read instruction manual
Disconnect the mains plug
if the cord is damaged
or entangled
The sound power level
indicates by Lw
A
in dB
Keep bystanders away. Do not mow whilst people especially children
or pets are in the mowing area.
Double insulated
Danger - High Voltage
Keep extension cord
away from cutting blades.
Always keep the lawnmower on the ground when mowing.
Tilting or lifting the lawnmower may cause stones to be thrown out.
Beware of severing toes or hands. Do not put hands or feet near
a rotating blade.
Blades continue to rotate after machine is switched off
STOP
Switch Off! Remove plug from mains before adjusting, cleaning or if
cable is entangled or damaged. Keep the cable away from the blade.
Don’t use on steep slopes.
Don’t use with rear flap
open.
Hertz
Watts
No load speed
96
CAUTION!:
DO NOT TOUCH ROTATING BLADES.
DESCRIPTION OF SYMBOLS
