background image

DESCRIPTION OF SYMBOLS

CARING FOR THE ENVIRONMENT

Power tools that are no longer usable should not be disposed of 

with household waste but in an environmentally friendly way. Please 

recycle where facilities exist. Check with your local council authority 

for recycling advice.

Recycling packaging reduces the need for landfill and raw materials. 

Reuse of recycled material decreases pollution in the environment. 

Please recycle packaging where facilities exist. Check with your 

local council authority for recycling advice.

SPARE PARTS

V

Volts

Hz

Hertz 

~

Alternating current

W

Watts

/min

Revolutions or 

reciprocation per minute

Double insulated 

Regulator compliance 

mark 

n

o

No load speed

Read instruction manual

                 

 

                 

 

                 

 

Blade ø180mm x ø20mm x 36TCT 

SPCCS1200-62

Blade Bolt & Washer 

 

SPCCS1200-59K

Carbon Brush (Pair)  

 

SPCCS1200-05

Carbon Brush Holder (Pair)   

SPCCS1200-04

Guard 

Spring 

  SPCCS1200-67

Guard 

   SPCCS1200-65

Spare parts can be ordered from the Special Orders Desk 
at your local Bunnings Warehouse.

For further information, or any parts not listed here, visit 
www.ozito.com.au or contact Ozito customer service 
Australia 1800 069 486 
New Zealand 0508 069 486 
E-mail: [email protected]

Summary of Contents for CCS-1200











Reviews: