background image

Note:

  To use the shoulder strap simply slide the strap over your 

shoulder so that some of the weight of the blower vac can 

be taken by your shoulder.

3   Connect the extension cord socket to the blower vac power 

cord.

Attaching & Removing the Patio Extension

Attaching the Collection Bag

Shoulder Strap

Removing the Collection Bag

Extension Cord Retainer

Note:

  To avoid the extension cord from detaching; always 

check that the cord is attached to the cord retainer before 

use.

2   Place the loop onto the cord 

retainer.

2   Pull the collection bag 

away from the housing.

1   To attach the patio 

extension push the head 

into the lowwer tube so it 

clicks into place.

2   To remove, push the 

tabs on the side of the 

extension out and then 

slide the head out.

1   Attach the clip on the 

collection bag to the hook 

underneath the upper tube.

1   Make a loop with 

the extension 

cord and push 

it through the 

square hole under 

the motor housing.

1   Pull down on the 

tab at the back of 

the collection bag 

connector.

2   Attach the plastic 

connector at 

the top of the 

collection bag to 

the outlet in the 

housing.

1   Ensure the shoulder strap 

is clipped onto the top of 

the blower.

2   To unclip the blower, press 

either side of the buckle.

Summary of Contents for BLV-2402









Reviews: