background image

GB

- 9 -

batteries. Frequent insertion of a charged 

or partly charged battery pack will result in 

over-charging and cell damage. Do not leave 

batteries in the charger for days on end.

8. 

Never use or charge batteries if you sus-

pect that the last time they were charged 

was more than 12 months previously. 

The-

re is a high probability that the battery pack 

has already su

 ered dangerous damage 

(exhaustive discharge).

9.  Charging batteries at a temperature below 

10°C will cause chemical damage to the cell 

and may cause a 

fi

 re.

10.  Do not use batteries which have heated du-

ring the charging process, as the battery cells 

may have su

 ered dangerous damage.

11.  Do not use batteries which have su

 ered 

curvature or deformation during the charging 

process or which show other non-typical sym-

ptoms (gassing, hissing, cracking,…)

12.  Never fully discharge the battery pack (re-

commended depth of discharge max. 80%) 

A complete discharge of the battery pack will 

lead to premature ageing of the battery cells.

13.  Never charge the batteries unsupervised.

Protection from environmental in

fl

 uences

1.  Wear suitable work clothes. Wear safety gog-

gles.

2. 

Protect your cordless tool and the battery 

charger from moisture and rain.

 Moisture 

and rain can cause dangerous cell damage.

3.  Do not use the cordless tool or the battery 

charger near vapors and in

fl

 ammable liquids.

4.  Use the battery charger and cordless tools 

only in dry conditions and an ambient tempe-

rature of 10-40°C.

5.  Do not keep the battery charger in places 

where the temperature is liable to reach over 

40°C. In particular, do not leave the battery 

charger in a car that is parked in the sunshine.

6. 

Protect batteries from overheating.

 Over-

loads, over-charging and exposure to direct 

sunlight will result in overheating and cell 

damage. Never charge or work with batteries 

which have been overheated – replace them 

immediately if possible.

7. 

Storage of batteries, battery chargers 

and cordless tools.

 Store the charger and 

your cordless tool only in dry places with an 

ambient temperature of 10-40°C. Store your 

lithium-ion battery pack in a cool, dry place at 

a temperature of 10-20°C. Protect them from 

humidity and direct sunlight. Only place fully 

charged batteries in storage (charged at least 

40%).

8.  Prevent the lithium-ion battery pack from free-

zing. Battery packs which were stored below 

0°C for more than 60 minutes must be dispo-

sed of.

9.  When handling batteries beware of electro-

static charge: Electrostatic discharges cause 

damage of the electronic protection system 

and the battery cells. Avoid electrostatic char-

ging and never touch the battery poles.

Rechargeable batteries and cordless electric 

machines and tools contain materials that are po-

tentially harmful to the environment. Never place 

any cordless electric machines or tools in your 

household refuse. When cordless electric machi-

nes or tools become defective or worn, remove 

the rechargeable batteries and return them to 

iSC GmbH (address: Eschenstrasse 6, D-94405, 

Germany). If the rechargeable batteries cannot be 

removed, return the complete cordless machine 

or tool.

You can then be sure that the equipment will be 

correctly disposed of by the manufacturer. 

When shipping or disposing of batteries and 

cordless tools, always ensure that they are 

packed individually in plastic bags to prevent 

short circuits and 

fi

 res.

Special safety information

• 

Read the operating instructions carefully. 

Familiarize yourself with the operator controls 

and proper operation of the machine.

• 

Never allow children or other persons who 

are not familiar with the operating instructions 

to use the equipment. Contact your local 

governmental agency for information regar-

ding minimum age requirements for the user.

• 

Never work in the direct vicinity of persons - 

especially children - or animals.

• 

Always keep in mind that the machine opera-

tor or user is responsible for accidents invol-

ving other persons and/or their property.

Anl_PXCTS_0182U_SPK7.indb   9

Anl_PXCTS_0182U_SPK7.indb   9

28.08.2019   08:59:57

28.08.2019   08:59:57

Summary of Contents for 34.312.04























Reviews: