DESCRIPTION OF SYMBOLS
Read instruction manual.
Nm
Newton Meters
Always keep the lawnmower on the ground when mowing.
Tilting or lifting the lawnmower may cause stones to be thrown out.
Beware of servering toes or hands. Do not put hands or feet near
a rotating blade.
Do not mow in the rain or leave the lawnmower outdoors while raining.
Keep bystanders away. Do not mow whilst people especially children
or pets are in the mowing area.
Blade continues to rotate after the machine is switched off. Wait until all
machine components have completely stopped before touching them.
Pull out Safety Key before
carry out any repair work.
Regulator compliance mark
96
Sound power level
The equipment`s operating time depends on the battery with
the lower charge level. Therefore, only use rechargeable
batteries which are charged to the same level.
TROUBLESHOOTING
Removing and Fitting the Blade
Cleaning, Maintenance and Storage
1. To remove the blade bolt, hold the blade
firmly and with a 13mm socket loosen the
blade bolt by turning it anti-clockwise.
NOTE:
A piece of timber will assist
in holding the blade while removing or
tightening the blade bolt.
2. Remove the blade bolt and blade.
3. To fit the blade, place the blade over the centre hole aligning the lugs.
4. Then retighten the fastening bolt with the universal wrench. The tightening torque
should be approx. 25 Nm.
• Keep all nuts, bolts and screws tight to be sure the lawn mower is in a safe working condition.
• Check the catcher frequently for wear or deterioration.
• Replace worn or damaged parts for safety.
• Only use the replacement blade and blade bolt specified for this product.
• Be careful during adjustments of the lawn mower to prevent entrapment of the fingers between
moving blade and fixed parts of the machine.
• When not in use, the mower should be stored in a dry, frost-free location, out of reach of children.
If the housing of the mower requires cleaning, do not use solvents but a moist soft cloth and brush
only.
• For best results, clean the lawn mower with a brush or rag.
Note: Ozito Industries will not be responsible for any damage or injuries caused by the repair of the
lawn mower by an unauthorised person or by mishandling of the lawn mower. This tool is designed for
DIY use - use in commercial or industrial environments will void the warranty.
WARNING!
ALWAYS ENSURE THE LAWN MOWER
BLADE HAS COMPLETELY STOPPED, REMOVE
SAFETY KEY, BATTERIES AND GRASS CATCHER
PRIOR TO ANY MAINTENANCE.
WARNING!
ALWAYS USE GLOVES WHEN HANDLING
THE BLADE. SHARP EDGES COULD CAUSE INJURY.
Problem Cause
Remedy
Mower is not
starting
Possible clogging
Check underneath the mower and clear out
as necessary
Battery is low in charge
Charge battery
Battery not inserted
properly
Insert battery pack correctly
Grass too long
Raise the cutting height to reduce starting
load
Safety key not inserted
correctly
Fit correctly
Telescopic handle
assembled incorrectly.
Ensure the Handle Angle Quick-release Lever
is secure on both sides and one of the three
positions available is selected.
Mower is
hard to push
Height of cut too low
Raise cutting height
Cutting blade blunt
Replace blade
Possible clogging
Check underneath the mower and clear out
as necessary
Grass too long
Raise the cutting height and walk slower
Grass too dense
Raise the cutting height and walk slower and
cut more frequently
Wet grass
Wait until the grass dries before mowing
Motor stops
while cutting
Height of cut too low
Raise the cutting height
Battery has no power
Charge batteries
Mower is
not catching
grass properly
Height of cut too low
Raise the cutting height
Wet grass
Wait until the grass dries before mowing
Mower
vibrating
Bent or damaged blade
Replace blade
Replace the metal blade after 50 hours mowing or 2 years
whichever is sooner. If the blade is cracked or damaged
replace it with a new one.
MAINTENANCE
Only replace the blade with a genuine Ozito replacement blade, as this will ensure top
performance and safety under all conditions.
Battery protection system
The tool is equipped with the battery protection system, which helps to ensure a long
service life.
The output power automatically cuts off during operation when the tool and/or battery are
placed under the following situations:
• When the tool is overloaded:
If this occurs, release the start/stop lever safety key and batteries and remove causes
of overload, then reinsert the safety key and batteries, then press and hold the lock-
off button and pull the start stop lever again to restart.
• When the remaining battery capacity becomes low:
Recharge the battery pack.
Note:
The indicated capacity may be lower than the actual level during use or
immediately after using the tool.
• Remove build up of grass in the grass chute.
• Keep all safety devices, air vents and the
motor housing free of dirt and dust as far as
possible. Wipe the equipment with a clean
cloth or blow it with compressed air at low
pressure.
• Do not clean the lawn mower with running
water, particularly with high-pressure water.
