background image

 

 

 

Oxford Technical Solutions Ltd. http://www.oxts.com 

Page 9 of 42 

 

 

Conformance notices 

The xNAV650 complies with the radiated emission limits for 47 CFR 15.109:2010 class A of  part 15 
subpart B of the FCC rules, and with the emission and immunity limits for class A of EN 55022. These 
limits  are  designed  to  provide  reasonable  protection  against  harmful  interference  in  business, 
commercial  and  industrial  uses.  This  equipment  generates,  uses  and  can  radiate  radio  frequency 
energy  and,  if  not  installed  and  used  in  accordance  with  the  instructions,  may  cause  harmful 
interference to radio communications. However, there is no guarantee that interference will not occur 
in  a  particular  installation.  If  this  equipment  does  cause  harmful  interference  to  radio  or  television 
reception, which can be determined by turning the equipment off and on, the user is encouraged to try 
to correct the interference by one or both of the following methods: 

 

Re-orient or relocate the receiving antenna. 

 

Increase the separation between the equipment and the receiver. 

The xNAV650  incorporates GNSS receivers. No GNSS receiver will be able to track satellites in the 
presence of strong RF radiations within 70 MHz of either the L1 GPS frequency (1575 MHz) or L2 (1228 
MHz). 

The xNAV650 conforms to the requirements for CE. 

The xNAV650 is certified for use with GNSS antennae with a gain of less than or equal to 35 dB. 

Regulator testing standards 

EMC 

 

BS EN 61326-2-1:2013 - Electrical equipment for measurement, control and laboratory use.  

 

BS  EN  301  489-19  v2.1.1  (2019-04) 

–  Electro  Magnetic  Compatibility  (EMC)  standard  for  radio 

equipment  and  services;  Part  19:  Specific  conditions  for  Receive  Only  Mobile  Earth  Stations 
(ROMES)  operating  in  the  1,5  GHz  band  providing  data  communications  and  GNSS  receivers 
operating in the RNSS band (ROGNSS) providing positioning, navigation, and timing data. 

LVD 

 

BS EN 61010-1:2010 - Safety requirements for electrical equipment for measurement, control, and 
laboratory use. 

RED 

 

BS  EN  303  413  V1.1.1  (2017-06)  -  Global  Navigation  Satellite  System  (GNSS)  receivers.  Radio 
equipment operating in the 1 164 MHz to 1 300 MHz and 1 559 MHz to 1 610 MHz frequency bands. 

RoHS 

 

BS  EN  50581:2012 

–  Technical  documentation  for  the  assessment  of  electrical  and  electronics 

products with respect to the restriction of hazardous substances. 

FCC 

 

47  CFR  15.109 

–  Code  of  Federal  Regulations  –  Title  47  (Telecommunication):  Part  15  (Radio 

Frequency Devices) 

– Subpart B (Unintentional Radiators) – Section 15.109. 

 

ICES-003 Issue 6 January 2016 

– Information Technology Equipment (Including Digital Apparatus) 

– Limits and Methods of Measurement. 

Summary of Contents for xNAV650











































Reviews: