Owon Waveform Generator Manual Download

Page: 6 / 16

Front

/Rear Panel and User Interface

⑩

Main output
terminal

Output main signal

⑪

Foot stool

Make the instrument to be tilted for ease of operation

⑫

Trigger key

Activate or deactivate the sync signal output. The button is lit
when it is in the On state.

⑬

Sync output
terminal

Output sync signal (see P12, "

To Set the Sync Output

⑭

Modulation

(Only for the model with "F")

Generate the Modulated waveforms

⑮

Burst

(Only for the model with "F")

Generate burst for Sine,

Square, Ramp, Pulse and Arbitrary waveform

⑯

Sweep

(Only for the model with "F")

Sweep Sine, Square or Ramp waveform

⑰

Waveform selection
buttons

Include: Sine

, Square

, Ramp

, Pulse

Noise

and Arbitrary

waveform. When a

waveform is selected, the backlight of the button turns on.

⑱

Power button

Turn on/off the generator

Rear Panel Overview

①

④

③

②

⑤

⑥

⑦

Figure 3-2 Rear panel overview (the model with "F" is shown)

①

Power socket

AC input connector

②

Fuse

The rating is 250 V

，

F2AL.

Summary of Contents for Waveform Generator

















Search results

Summary of Contents for Waveform Generator

Reviews:

Related manuals for Waveform Generator

Brands by name

Popular brands

Owon Waveform Generator, Manual

Search results

Summary of Contents for Waveform Generator

Reviews:

Related manuals for Waveform Generator

Brands by name

Popular brands