ERECTION INSTRUCTIONS.
Outdoor revolution tents are all erected outer first
1.
Lay the outer/flysheet spread out on the ground. Slacken adjusters off on the black tapes (near the ring
and pin assemblies) around the foot of the awning.
2.
Open the pole bag and lay the poles out on the ground. Then open the poles out ensuring they are all
correctly seated in the ferrulls, as most damage is done to awnings at this stage before attempting to
erect. SPARE POLES CAN BE PURCHASED FROM
WWW.OUTDOOR-REVOLUTION.COM
, spares
section.
3.
You will notice the poles have different coloured ends to them, match this pole colour to the pole sleeve on
your outer.
4.
When the poles are matched, proceed to slide carefully through the seam to the other side (taking care
not to force it through) starting at one end and working across the awning. Continue to do this with all the
remaining poles
5.
Place the steel pin (part of the ring and pin assembly) at the base of the awning flysheet into the bottom of
each pole, one at a time,
along one side of the tent.
6.
Now take the opposite end of the pole and push steadily, whilst holding the metal ‘ring & pin’ assembly at
the foot of the awning, when the pole is fully through, put the pin into the bottom of the pole
.
Tip. When
erecting larger tents it is useful for someone to get under the canvas and push the tent upwards to
ease pressure on the poles
This will now have formed the awning shape. Continue to repeat this
process with the remaining poles.
7.
You are now ready to peg the tent out.
Tip. Pegs work best when angled 45 degrees to the ground
.
8.
Starting at the front of the awning, peg all the pegging points and then work backwards across the tent.
(
Take care not to over tighten the tent,
if a door zip is tight it is possible the awning is over tensioned)
9.
Drive your vehicle up to the drive-away tunnel (at the side of the awning) and proceed to attach by
whichever system is appropriate for your vehicle (if you are not sure which is the best system to use ask
your dealer for advise) Peg out and tension the elastic on the tunnel in order to achieve a weather seal
against your vehicle.
10.
Guy lines can now be tensioned and pegged, please ensure that in heavy weather you use
ALL GUY
LINES AND STABILITY STRAPS
however it is advisable to use these at all times as a precaution.
Do
remember
that failure to use guy lines may result in damage to your awning.
***Note
, to attach the Navigator Kombi to a Motorhome Fiamma/Omnistor you will need to purchase a driveaway
kit consisting of double edged awning piping an figure 8 joining strips. Simply slide into the awning rail, then the
tent is lined up and the figure 8 is positioned to join the two.
ADDITIONAL FEATURES ON YOUR NAVIGATOR KOMBI
1) Fibre pole system for ease of assembly and greater stability.
2) Fly screens on both doors
3) Ring & pin system at foot of awning to locate poles
4) Pockets on tunnel to stow tunnel panel
5) Locating points to take inner tent (optional extra)
Please note these few points for trouble free camping.
a.
After use please you always dry and air the tent before packing away.
b.
Any dirt or stains can be removed by brushing or gently washing with warm water. DO
NOT use detergents as this will destroy the waterproofing on the fabrics.
c.
We advise that you DO NOT cook or smoke in this tent; although the outer fabric is fire
retardant treated it will still melt.
d.
Please make sure that you have a good time.
**We highly recommend that you insure your awning against storm damage or
accidental damage, as the warranty does not cover such eventualities. The
manufacturer is not liable for any damage caused to the caravan or vehicle
because of misuse, incorrect pitching or extreme weather**
Outdoor Revolution Tents are distributed by:
Blue Diamond Products Ltd
