background image

11

• 

Adults and children should stay away from high temperature surface to avoid 

burns or clothing ignition.

• 

Children should be carefully supervised when they are in the area of the heater.

• 

Clothing or other flammable materials should not be hung on the heater or 

placed on or near the heater.

• 

To close the gas supply at the valve of the gas cylinder or the regulator after use;

• 

In the event of gas leakage, the appliance shall not be used or if alight, the gas 

supply shall be shut off and the appliance shall be investigated and rectified 

before it is used again;

• 

To check the hose at least once per month

,

 each time the cylinder is changed

or 

each time before long time no use. If it shows signs of cracking, splitting or other 

deterioration it shall be exchanged for new hose of the same length and of the 

equivalent quality;

• 

The use of this appliance in enclosed areas can be dangerous and is 

PROHIBITED;

• 

Read the instructions before using this appliance. The appliance must be 

installed in accordance with the instructions and local regulations.

• 

For connection of hose and regulator,and connection of regulator and hose, 

please refer to photo showed above.

• 

Remove plastic wrap from any part before lighting.

• 

Never cover a heater until it has completely cooled.

• 

If you have any queries regarding these instructions, contact your local dealer.

• 

To change the gas cylinder in a amply ventilated area, 

away from any ignition source (candle, cigarettes, other 

flame producing appliances, ...);

• 

To check that the regulator seal is correctly fitted and 

able to fulfill its function showed as photo right;

• 

To not obstruct the ventilation holes of the cylinder 

housing;

Hose/ Regulator connection and

Regulator / Cylinder connection

seal

hose

regulater

cylinder

CEILING

W

A

L

L

100 cm

100 cm

Fortification of base to the ground

HEATER STAND AND LOCATION

• 

The heater is primarily for outdoor use only. Always 

ensure that adequate fresh air ventilation is provided.

• 

Always maintain proper clearance to combustible 

materials, i.e. top 100 cm and sides 100 cm minimum.

• 

Heater must be placed on level firm ground.

• 

Never operate heater in an explosive atmosphere 

like in areas where gasoline or other flammable 

liquids or vapors are stored.

• 

To protect heater from strong wind, anchor the base 

securely to the ground with screws.

Summary of Contents for OUT370609/PH100T

















Reviews: