Outback OUT370609/PH100T Assembly And Operating Instructions Manual Download Page 8 | Manualshive

Page: 8 / 16

background image

8

7

8

Fasten the reflector with 3 pcs Large Flat Washers and 3 pcs Wing Nuts.

7-1. Check whether the connection of vertical post and burner are

assembled according to instructions, and all bolts and nuts are tightened.

7-2. Put 6 pcs Large Flat Washers on 3 Reflector Spacers.

Reflector Spacer

Reflector

Wing nut

«
...
6
7
8
9
10
...
»

Summary of Contents for OUT370609/PH100T

















Reviews:

No comments

Related manuals for OUT370609/PH100T

Brand: wallas Pages: 43

Brand: wallas Pages: 109

Brand: Rheem Pages: 28

StreetHeat SR-28

Brand: INTEGRATED PAVING CONCEPTS Pages: 21

Platinum GHOR900

Brand: Goldair Pages: 16

Brand: Cocoon Concept Pages: 5

Comfort SC-FH53015

Brand: Scarlett Pages: 8

Brand: Holmes Pages: 2

Brand: P.Lindberg Pages: 26

Brand: GE Pages: 16

Brand: Gasmate Pages: 8

Bristol DX 8762

Brand: HearthStone Pages: 41

Brand: Micasa Pages: 4

Brand: Lochinvar Pages: 68

Pilot Light Ignition

Brand: L.B. White Pages: 21

Brand: KERO Pages: 30

EIWH electronicVED pro Series

Brand: Vaillant Pages: 12

Brand: Haverland Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands