Oursson JM3400, Instruction Manual

Page: 5 / 20

5
1. Assemble the device as described in the previous sec-
tion.
2. Plug the device into an electrical outlet.
3. Turn on the device, turning the knob in «1» or «2» posi-
tion.
4. With the help of the pusher place beforehand washed
and, if necessary, peeled and chopped ingredients into
the feeding chute. Fruit with a large seed, such as
plum, apricot or peach, remove the seeds before
making juice from them.
5. After finishing juicing turn it off and unplug it.
The ingredients must be placed in small portions, to not
overfill the cup. Use the pusher to push ingredients. In addi -
tion, the pusher will help avoid splashing the juice from the
feeding chute, when squeezing juicy products.
At the end of juicing, close the lid of the spout so that
the remnants of juice do not drip on the table.
TIP:
It is recommended to drink fresh juices immediately
after preparation, because after a while they begin to flake,
lose useful properties and attractiveness.
UTIlIzATION
ORDER OF OPERATION
Before first use, wipe the device with a soft, dry cloth.
The rest of the parts
wash with warm water and
detergent. Before assembling or disassembling the
device and / or removing attachments, make sure
that the device is unplugged.
The order of assembly Рiс. B.
• Place the motor unit on a flat and clean surface.
• Assemble the device according to the picture:
• Install the filter insertion onto the motor unit
• Insert filter into the filter insertion
• Install pulp container
• Install the lid
• Fixate the catch onto the juice maker’s lid.
• Place under the spout a container for juice with lid
• Place the pusher into the feeding chute
EMPTYINg THE PUlP CONTAINER AND
MESH FIlTER:
• Turn off the device, turn the knob to “0” mark.
• Detach the pulp container form the motor unit.
Empty the container.
• Install the pulp container back.
• Mesh filter must be emptied if:
• Motor unit’s rotating speed has lowered
• Juice is too thick
• The device starts to vibrate
NOTE: Pulp container must be emptied before the pulp
level reaches edge of the tray. It is recommended to empty
the pulp container and mesh filter at the same time.
DISASSEMBlINg THE JUICE MAKER:
• Turn off and unplug the device.
• Wait till the motor unit stops, approximately 10
sec.
• Remove the pusher and pulp container.
• Lower the catch and remove the lid.
• Remove the mesh filter.
• Remove the filter insertion from the motor unit.
NOTE: If the device begins to vibrate, it means that the
mesh filter is clogged or damaged. Turn off the device and
check the mesh filter status.
Before opening the device, make sure the
motor unit is fully stopped.
The motor is equipped with a protective
setting that automatically shuts down the
device in case of overload and restarts it after
cooling down.
Damaged mesh filter must not be used.
The device is equipped with a safety lock. It
won’t be possible to turn on the device if the
catch isn’t fixated on the lid.
To avoid overheating of the motor, do not use
this device for more than 4 minutes without
a pause. Every 4 minutes make a 5-minute
break and let the device cool down.
To push the ingredients into the feeding chute,
use only the pusher, which is included with the
device. It is strictly forbidden to push ingredi-
ents with hands, as this could cause injury.
PREPARATION RECOMMENDATIONS:
1. Do not place into the device dried or hard ingredi-
ents, such as whole grains, fruits with hard seeds,
thick-skinned or ice. This can damage juice maker’s
parts.
2. Do not press the products without juice content
(coconut, sugar cane, whole grains, etc.).
3. Do not use ingredients that contain an excessive
amount of vegetable oil or animal fat. Do not use the
juice maker for squeezing oil from the ingredients.
4. Do not load pulp into the juice maker.
5. After juicing the ingredients with small seeds, you
must clean all parts of the device from the seeds.
6. The amount of juice depends on the freshness and
juiciness of the products. The fresher the vegetables
or fruit, the more juice you can make.
Ingredients Preparation Speed Note
Apple (pear, quince,
etc.)
Medium size fruits may be placed
without preparation. Big ones-cut.
Remove the peduncle.
1 Cut the damaged fruit pulp.