manualshive.com logo in svg

OUMAN M-LINK, Manual

Share
Download
OUMAN M-LINK Manual Download Page 11

11

1.  You can deactivate the function at “DHCP in use”.  (If the DHCP function is on, the 

manual changes will be bypassed at IP address , Subnet mask, Gateway address and 
Name server address).

2.  Ask the network administrator for the network settings and enter the desired settings.
3.  Select “Confirm”.

Alternative 2:  Setting the IP address manually:

This requires that network has DHCP service that assigns an IP address for 

M-Link

. 

1.   Select “DHCP in use” .
2.   Select ”Confirm”. 
3.   Wait approximately one minute.

4.  Select 

. If the IP settings changes, the new IP settings have been successfully 

received. If the IP settings do not change, make sure the connections are correct and 
that the network has a DHCP server.

5.  If you select “Ouman Access in use”, M-Link retrieves the Access IP address

1

2

5

There are two alternative ways to set the M-Link device IP address and 

network settings:

1. IP address is retrieved via DHCP function. 

2. IP address is set manually.

 

Alternative 1. Setting the IP address via DHCP function: 

Settings

Alarm routing:

Network

Setting

Factory setting

Description

SNMP server IP 

10.1.1.23

The IP address of the destination server where the message is sent. Ounet’s 
IP address 10.1.1.23 is the default.

Retry delay

5 min

If the alarm is not acknowledged from the server, the alarm message will be 
resent after the delay that is set.

SNMP in use

This selection enables/disables the entire SNMP function. 

The SNMP function can be used for alarm transfers between Ouman devices and the control room. 

The SNMP func-

tion can be used for sending information on the activation, elimination and resetting of alarms to the desired server using the SNMP 
protocol.

FTP in use:  

With FTP enabled, you can download the template file to Ounet directly 

from the device (see page 4).

Setting

Factory setting

Description

HTTP server address

The IP address of the destination server where the message is sent.

HTTP alarm in use 

This selection activates the sending of alerts via HTTP messages.  

Please note: If Access connection is used, M-Link’s Access IP address or name (m

xxxxxxxx

.ouman.net) must also be set at 

Ounet as the local IP address.

From the M-link device, information about alarm can also be transmitted using the HTTP protocol.

192.168.1.1

192.168.1.254

255.255.255.0

8.8.8.8

xx.xx.xxx.xxx

Summary of Contents for M-LINK

















Reviews:

No comments

Brands by name

Popular brands

Load more brands