background image

2

Label on the device

ISED non-interference disclaimer

 

This device contains licence-exempt transmitter(s)/receiver(s) that comply with  

 

Innovation, Science and Economic Development Canada’s licence-exempt RSS(s).  

 

Operation is subject to the following two conditions:

 

1. 

This device may not cause interference

 

2. 

This device must accept any interference, including interference that may cause  

 

undesired operation of the device.

 

L’émetteur/récepteur exempt de licence contenu dans le présent appareil est  

 

conforme aux CNR d’Innovation, Sciences et Développement économique Canada  

 

applicables aux appareils radio exempts de licence. L’exploitation est autorisée  

 

aux deux conditions suivantes :

 

1. 

L’appareil ne doit pas produire de brouillage;

 

2.

  L’appareil doit accepter tout brouillage radioélectrique subi, même si le  

 

brouillage est susceptible d’en compromettre le fonctionnement.          

RF Exposure statement for ISED

 

This equipment complies with ISED RSS-102 radiation exposure limits set forth for  

 

an uncontrolled environment. This equipment should be installed and operated  

 

with minimum distance 20 cm (7.6 inches) between the radiator and any part of  

 

your body. This transmitter must not be co-located or operating in conjunction  

 

with any other antenna or transmitter.

 

    

 

Our se conformer aux exigences de conformité ISED RSS-102 RF exposition, une  

 

distance de séparation d'au moins 20 cm doit être maintenue entre l'antenne de  

 

cet appareil et toutes les personnes. Lanceurs ou ne peuvent pas  

 

 

coexister cette antenne ou capteurs avec d'autres.

RF Exposure statement for FCC

 

This equipment complies with FCC radiation exposure limits set forth for an  

 

uncontrolled environment. This transmitter must not be co-located or operating in  

 

conjunction with any other antenna or transmitter. In order to avoid the    

 

possibility of exceeding the FCC radio frequency exposure limits, this equipment  

 

should be installed and operated with minimum distance 20 cm (7.8 inches)  

 

between the antenna and your body during normal operation. Users must follow  

 

the specific operating instructions for satisfying RF exposure compliance.

M/N: GA3020
F/W: 1.0

IC: 12649A-BEDHT

 

FCC ID: 2ADQFBEDHT

 

FAIT AU 

CANADA

Barcode

Summary of Contents for GRANBY GRA-0035














Reviews: