background image

1 Safety Precautions

1.1 Power Safety Precautions

• The system should be plugged into a normal UK 3 pin plug at your home

   or workplace and not be used in addition to AC 220-240V, 220V.

• Should be used in a grounding socket with rated current above 10A.

• Should only be used on an electrical circuit with RCD.

• Please do not use this product if the power cord or plug is damaged or

   when the plug is loose.

• If there is dust or water and other foreign matter on the power plug,

  please wipe it clean before use.

1.2 Setup Precautions

• The system should not be installed near heating equipment, electric

   heating products or other high-temperature places.

• The system should not be installed in a place of possible leakage of

   combustible gases or near any flammable substances.

• The system should only be used indoors and positioned on a stable flat

   surface avoiding direct sunlight and moisture.

Thank you for purchasing this product, please read this manual carefully

before using the system, and keep it for future reference. If you have any

questions about this machine, please call our customer service centre on

0800 002 9533. 

Take Note: Boiling water is potentially dangerous. 

It is the responsibility of the owner to take sensible precautions when operating 

the boiling water function of the system and to instruct other family members 

and other new users to operate it safely. 

KEEP OUT OF REACH OF CHILDREN

Summary of Contents for Zero IP-II




















Reviews: