background image

P/N 101023281 

Metor 900M 

Page 

11

 

Rev. 0.5 

 

Installation and Operating Manual 

 

 
Rapiscan Systems Proprietary Information 

2.4  Battery Backup Set 

 

A battery backup accessory MBBS5332, Rapiscan part number 101010726, is available for 
emergency power in case of power outage. 
 
The battery backup guarantees uninterrupted operation in case of a temporary power outage. 
The unit is installed inside the cross piece. 
 
For more information on battery backup refer to its manual. 

 
 
2.5  Technical Data 

 
 

Power 

 

 

Voltage, nominal ..................................... 100 

– 240 VAC 

 

Voltage, absolute limits ........................... 90 

– 264 VAC 

 

Frequency............................................... 47 

– 63 Hz 

 

Power consumption, typical ..................... 30 W 

 

Power consumption, maximum ............... 65 W, with battery backup charging 

 

Power consumption, at standby............... 6 W 

 

 

Recommended operating conditions 

 

 

Environment ........................................... both outdoor and indoor use 

 

Ambient temperature............................... -20 °C 

– +60 °C / -4 °F – +140 °F 

 

-15 °C 

– +45 °C / +5 °F – +113 °F, 

 

when battery backup is in use 

 

Storage temperature ............................... -40 °C 

– +70 °C / -40 °F – +158 °F 

 

Relative humidity..................................... 0 

– 100 % 

 

Elevation ................................................. max. 3000 m / 9840 ft 

 

Ingress protection rating .......................... IP65 

 

Pollution degree ...................................... 2 

 
 

Dimensions and weight 

 

 

Height ..................................................... 224 cm / 88 in 

 

Internal height ......................................... 206 cm / 81 in 

 

Width (standard) ..................................... 87 cm / 34 in 

 

Width (with extension set) ....................... 92 cm / 36 in 

 

Internal width (standard).......................... 76 cm / 30 in 

 

Internal width (with extension set) ........... 82 cm / 32 in 

 

Depth ...................................................... 65 cm / 26 in 

 

Weight .................................................... 60 kg / 133 lbs 

 
 

 

 

 

Summary of Contents for Rapiscan Orion Metor 900M




































Reviews: