ORTAL Circle 70 User Manual Download | Manualshive

Page: 18 / 39

background image

[Installation

–

Curved Fireplaces

18

[

FLAT GLASS PANEL INSTALLATION:

•

While the cover is positioned on top of the flat glass,
make sure that the high temperature seal is still in
place, and attach the top trim to the correct position.

•

Make sure that the glass panel edges do not exceed
the outer top cover circumference. This enables the
outer curved glass installation in the next steps.

«
...
16
17
18
19
20
...
»

Summary of Contents for Circle 70








































Reviews:

No comments

Related manuals for Circle 70

Brand: Jøtul Pages: 36

Brand: Dik Geurts Pages: 96

Majestic SB5400SS

Brand: Majestic Pages: 36

Brand: Bioprom Pages: 14

Kingsman Marquis MCVP42N

Brand: R-Co Pages: 65

Brand: Napoleon Pages: 128

Brand: Allen + Roth Pages: 40

Brand: Northline Express Pages: 35

Brand: Bold Flame Pages: 22

Silverton G8600

Brand: RealFlame Pages: 8

Brand: Warmlite Pages: 12

attika 600 MAX-1

Brand: RAIS Pages: 26

Brand: Valor Pages: 12

Brand: Element4 Pages: 12

Brand: Outfit Pages: 37

Brand: Qindao Hichanse Group Pages: 16

Brand: Napoleon Pages: 124

Brand: Napoleon Pages: 112

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands