background image

Caution: the system is wireless RF product; therefore, it may not receive a signal due to the poor environment or 

incorrect operating either on incorrect installation. When the system continually cannot receive any signal from any 

tire sensor more than 10 minutes since the system has been switch on for monitoring, the system will shown “ E2 ” 

and turn on the RED abnormal LED light with alert sound. In this case, it may cause by a RF interference 

environment, a driver need to drive the vehicle and leave the place where are running. If the display still cannot 

receive any correct signal from tire sensor, then, a driver need to find a close qualified tire maintain service for 

checking or maintain. It may cause by a tire sensor damages or battery power consumption. (Battery in normal 

condition can be used more than 7 year, but in abnormal condition, the tire sensor will continually send warning 

signal to the driver, thus it wills consumption the battery quickly than normal prediction.) 

W401A Tire Pressure Monitoring System 

ORO-W401A Tire Pressure Monitoring Systems (TPMS), can monitor and provide tire pressure, tire temperature 

and car battery information by real time to help the driver to control and keep the normal tire pressure in order to 

reduce the fuel consumption and extend the tire life, and also through the battery information, the driver can 

change the battery before happens any bug and reduce the % of vehicle breakdown on the road.   

 

ORO-W401A Tire Pressure Monitoring System, includes 4 tire sensors and 1 receiver display, the 

TPMS can monitoring the pressure/temperature by snap-in installation into the tire, and transmit the 

tire information to the receiver by wireless. The TPMS display will alarm when any abnormal happens 

to the tire in order to prevent any possible accidents which may happen to the driver/vehicle.   

 

W401A TPMS Specification 

1. Tire Sensor’s Specification                                                                                               

 

Battery life 

3~5 years normally use. 

Battery Voltage 

3.6 V 

Storage Temperature 

-40

 

to 125 

 

Operation Temperature 

-30 

 to 120 

 

Operation Frequency 

433.92MHz 

±

4.25MHz 

Transmission Frequency 

Transmit 1 signal each 30 sec. 

Pressure Monitoring Range 

0 ~ 800 kPa 

Pressure Reading Accuracy 

±

10kPa 

Temperature Monitoring Range 

-30 

 to 100 

 

Temperature Reading Accuracy 

±

4

 

 

2. 

Receiver Specification                                                                                                                             

Operation Voltage 

9V ~ 15V 

Normal Operation Voltage 

200mA 

Summary of Contents for W401A























Reviews: