background image

 3

SM0974023 A 01

Monitor 12” RLED, Art. No. 84002575

1. Introduction

With this Orlaco Loadview system the crane operator can see 

immediately on his monitor when a lifting operation could possibly 

become dangerous. The operator is no longer dependent on information 

from other persons by means of a portable radios. He can make the right 

decisions without delay and thus prevent accidents on site. There is also 

a far lesser chance of any misunderstandings occurring as the Loadcam 

system makes it possible for the operator to verify the instructions from 

the banksman. The Loadcam below the quick fit set on the tower crane 

trolley, is looking straight downwards on top of the hook and the load. 

On the color monitor in the crane cab, the operator receives at all times, 

a crystal clear image of the position of the hook. When necessary he can 

zoom in on the hook for a more detailed image. All is possible!

2. Precautions

Set 

Loadview

 Tower crane (12” RLED), Art. No. 84060746

 1.

 There should be no obstructions between the transmitter and receiver, 

the components should always be in “direct view” of one  another.

 2.

 

Make sure that the connector sides of the transmitter and receiver are facing each other and that the connectors are facing down.

 3.

 

The transmitter and receiver come as a pair. If replacement is required, the two components must be replaced as a set. 

  

 4.

 The long side of the zoom camera should be mounted on the side of the tip of the boom.

 5.

 

Between the cover of the battery pack and the battery, there are two wires with a connector. If the battery is not used for more than three days, the  

    connector must be disconnected. After re-inserting the connector, reactivate the battery pack by charging it for a short time.

 6.

 

The monitor display shows a battery; this indicates the charge level of the battery.

 7.

 

The battery should be charged after each working day.

 8.

 

If you have any other questions, please contact the Manitowoc Service Department on telephone 33 (0)4 72 81 51 51

System manual

Please note that the following is very important:

Read this chapter very carefully!

Summary of Contents for 84002575













Reviews: