Orion LBI-38888K Operator'S Manual Download Page 59

Page: 59 / 84

TURNING SCAN ON

1. Toggle scan operation ON by pressing

. The

SCAN indicator will

turn ON when the radio is scanning.

Scanning will stop while microphone is OFF-hook if hookswitch feature
is enable through programming.

2. When a channel on the scan list receives a channel assignment, the radio

unmutes on the assigned channel,

BSY

indicator comes ON and the

received scan channel is displayed.

•

The radio will continue scanning if a new channel is selected when
scan is ON.

•

Pressing the PTT button when scan is ON will cause the radio to
transmit on the displayed channel or to the currently selected channel
depending on programming.

•

Pressing

when scan is ON will cause the radio to recall the

scanned channel that was last received. This channel is recalled for a
period equal to the scan hang time.

TURNING SCAN OFF

Toggle scan operation OFF by pressing

. The radio will resume

operation on the selected channel.

NOTE

Summary of Contents for LBI-38888K





















































































Search results

Summary of Contents for LBI-38888K

Reviews:

Related manuals for LBI-38888K

Brands by name

Popular brands

Orion LBI-38888K, Operator'S Manual

Search results

Summary of Contents for LBI-38888K

Reviews:

Related manuals for LBI-38888K

Brands by name

Popular brands