Quick Installation Guide
Version 1.0
Q
uick
I
nstallation
G
uide
PRINTED ON RECYCLED PAPER
Q I G
1907-200-+11-FX010
Introduction
INJ-101GT++ PoE Injector series
The
is not only an IEEE802.3at compliant
device but also an advanced high power PoE injector. It is intelligent
detection that provided 1-ports 10/100/1000Base-T (X) PoE outputs. The
device does not turn on power until it detects a valid PoE signature from the
PoE devices attached downstream on the Ethernet cable. This protection
against damage to non-PoE compliant equipment which may be connected to
the Ethernet cable. Therefore, only an IEEE 802.3at/802.3af compliant
device can be powered with the
PoE Injector. Typically in
INJ-101GT++
Gigabit networks the maximum allowable CAT5 cable length is about 100
meters, due to the limitation of the Ethernet standards. The
INJ-101GT++
PoE Injector can function with any PoE P.D. equipment which is fully
compliant with the IEEE 802.3af/at PoE standards, and provide the DIP
switch configurator for High power PoE management.
Package Contents
The device is shipped with the following items. If any of these items is
missing or damaged, please contact your customer service representative
for assistance.
Features
I N D U S T R I A L
GIGABIT
Injector
PoE
Industrial Gigabit PoE++ Injector
INJ-101GT++-100W Series
PoE++ Injector for 1x10/100/1000Base-T(X)
Fully compliant with IEEE802.3at/802.3af standard
Auto protection for Over Voltage Power Input and over current output
Supports totally Power Output up to 100 Watts
Support wide range power input, 12 to 57VDC (-24V Model Only)
Provided DIP switch configurator for PoE mode management
High reliability and rigid IP-30 housing
DIN-Rail and wall-mount enabled
1. Gigabit PoE port
2. PoE indicator
3. DIP switch for PoE mode
4. Gigabit Data port
5. PoE power indicator
PWR
10/100/1000T
Data IN
PoE OUT
PoE
Sync
PoE Mode
Async
INJ-101GT++-100W-24V
1
4
5
2
3
41.0
9
5
.0
PWR
10/100/1000T
Data IN
PoE OUT
PoE
Sync
PoE Mode
Async
INJ-101GT++-100W-24V
Contents
Pictures
Number
X 1
QIG
X 1
25mm DIN-rail kit
X 1
Wall-Mount Kit
X 2
For INJ-102GT++
40mm DIN-rail kit
X 1
Wall-Mount Kit
X 2
For INJ-102GT++-24V
INJ-101GT++-100W or
INJ-101GT++-100W-24V
Installation
Preparation
Before installation, make sure you have all of the package contents available and a PC
with Microsoft Internet Explorer 6.0 or later, for using web-based system management
tools.
Elevated Operating Ambient:
If installed in a closed environment, make sure the operating
ambient temperature is compatible with the maximum ambient temperature (Tma)
specified by the manufacturer.
Make sure the amount of air flow required for safe operation of the
Reduced Air Flow:
equipment is not compromised during installation.
Mechanical Loading:
Make sure the mounting of the equipment is not in a hazardous
condition due to uneven mechanical loading.
Circuit Overloading:
Consideration should be given to the connection of the equipment to the
supply circuit and the effect that overloading of the circuits might have on overcurrent
protection and supply wiring. Appropriate consideration of equipment nameplate ratings
should be used when addressing this concern.
Safety & Warnings
21.9
13.1
24.7
22.52
DIN-rail
Step 1 :
Slant the device and screw the Din-rail kit onto the back of the device, right in the middle of
the back panel.
Step 2 :
Slide the device onto a DIN-rail from the Din-rail kit and make sure the device clicks into the
rail firmly.
Backplane-Mount
Step 1:
Screw the two pieces of backplane-mount kits to the top and bottom panels of the device. A
total of ight screws (mertric 3 x3) are required, as shown below.
e
Step 2:
Use the device, with wall mount plates attached, as a guide to mark the correct locations of
the four screws.
Step 3:
Insert a screw head through middle of the keyhole-shaped aperture on the plate, and then
slide the device downwards. Tighten the screw head for added stability.
70.0
4
3
.5
3
3
.6
8
.0
14.0
13.5
40.0
5
0
.0
2
5
.3
2
9
.0
41
2
4
.7
Ø5.9
Ø3.0
Dimension
Unit =mm (Tolerance ±0.5mm)
INJ-101GT++-100W-24V
4
3
.5
8
.0
14.0
6.05
25.0
5
0
.0
2
5
.5
1
2
.3
13.1
24.3
25.6
2
4
.3
Ø5.9
Ø3.0
21.9
22.52
70.0
INJ-101GT++-100W
Panel Layouts
Front Panel
1. Din-rail screw holes
Rear Panel
1
Top Panel
1
1. Terminal block
2. Wall-mount screw holes
2
1
1
2
26.1
9
5
.0
PWR
10/100/1000T
INJ-101GT++-100W
Data IN
PoE OUT
PoE
Sync
PoE Mode
Async
PWR
10/100/1000T
INJ-101GT++-60W
Data IN
PoE OUT
PoE
Sync
PoE Mode
Async
1
4
5
2
3
INJ-101GT++-100W Series
