Quick Installation Guide
Version 1.0
Q
uick
I
nstallation
G
uide
Introduction
PRINTED ON RECYCLED PAPER
The
is a modular managed industrial Ethernet switch with
twelve 10/100/1000Base-T(X) ports and two 100/1000Base-X SFP ports.
The Gigabit ports provide high network throughputs to give your network the
capacity to handle huge workloads. The SFP ports can meet demand for
long-distance data transmission. The switch comes with two modular slots
to provide more Ethernet ports. The modules support hot-swap installation;
therefore, you don’t need to power off the switch when replacing the
module. The switch also supports Ethernet Redundancy protocol, O-Ring
(recovery time < 30ms over 250 units of connection) and MSTP (RSTP/STP
compatible) to protect mission-critical applications from network
interruptions or temporary malfunctions with fast recovery technology. With
a wide operating temperature from -40 C to 75 C, the device can be
managed centrally via Oring’s proprietary Open-Vision platform as well as
via Web-based interfaces, Telnet, and console (CLI). The switch is one of
the most reliable choices for highly-managed and fiber Ethernet
applications.
IGS-9122GPM
o
o
Dimension
Panel Layouts
1. Power System LED
2. Power2 LED
3. Ring status LED
4. Fault indicator
5. Power1 LED
6. R.M. (Ring Master) LED
7. Reset button
8. Power input
9. Console port
10. Link/Act LED for SFP port
11. SFP port
12. Link/action LED for Gigabit Ethernet ports
13. Gigabit Ethernet ports
14. Speed LED for Gigabit Ethernet ports
Package Contents
Contents
DIN-rail Kit
CD
IGS-9122GPM
Pictures
Number
X 1
X 1
X 1
Front View
The device is shipped with the following items. If any of these items is
missing or damaged, please contact your customer service representative for
assistance.
GIGABIT
I N D U S T R I A L
SWITCH
Industrial Modular Managed Gigabit
Switch
QIG
Console Cable
X 1
X 1
8
4
5
6
Rear View
2
1
1. Wall-mount screw holes
2. Din-rail screw holes
Installation
Step 1:
Step 2:
Slant the switch and screw the Din-rail kit onto the back of the switch, right in the
middle of the back panel.
Slide the switch onto a DIN-rail from the Din-rail kit and make sure the switch clicks
into the rail firmly.
DIN-rail Installation
Q I G
IGS-9122GPM
1907-2-29-IGS9122GPM-1.0
Mechanical Loading:
Circuit Overloading:
Mounting of the equipment in the rack should be such that
a hazardous condition is not achieved due to uneven mechanical loading.
Consideration should be given to the connection of the equipment
to the supply circuit and the effect that overloading of the circuits might have on
overcurrent protection and supply wiring. Appropriate consideration of equipment
nameplate ratings should be used when addressing this concern.
Network Connection
The switch provides standard Ethernet ports. According to the link type, the switch uses
CAT 3, 4, 5,5e UTP cables to connect to any other network devices (PCs, servers,
switches, routers, or hubs). Please refer to the following table for cable specifications.
Cable Types and Specifications:
14
10
Preparation
Before you begin installing the switch, make sure you have all of the package
contents available and a PC with Microsoft Internet Explorer 6.0 or later, for
using web-based system management tools.
Elevated Operating Ambient:
Reduced Air Flow:
If installed in a closed or multi-unit rack
assembly, the operating ambient temperature of the rack environment may be
greater than room ambient. Therefore, consideration should be given to
installing the equipment in an environment compatible with the maximum
ambient temperature (Tma) specified by the manufacturer.
Installation of the equipment in a rack should be such
that the amount of air flow required for safe operation of the equipment is
not compromised.
Safety & Warnings
1
2
3
7
9
11
12
13
1
1
1
Cable
Type
Max. Length
Connector
10BASE-T
Cat. 3, 4, 5 100-ohm
UTP 100 m (328 ft)
RJ-45
100BASE-TX
Cat. 5 100-ohm UTP
UTP 100 m (328 ft)
RJ-45
1000BASE-T
Cat. 5 / Cat. 5e 100-ohm UTP
UTP 100 m (328 ft)
RJ-45
For pin assignments for different types of cables, please refer to the following
tables.
10/100 Base-T(X) MDI/MDI-X
Pin Number
MDI port
MDI-X port
1
TD+(transmit) RD+(receive)
2
TD-(transmit)
RD-(receive)
3
RD+(receive) TD+(transmit)
4
Not used
Not used
5
Not used
Not used
6
RD-(receive)
TD-(transmit)
7
Not used
Not used
8
Not used
Not used
Note: “+” and “-” signs represent the polarity of the wires that make up each
wire pair.
1000Base-T MDI/MDI-X
Pin Number
MDI port
MDI-X port
1
BI_DA+
BI_DB+
2
BI_DA-
BI_DB-
3
BI_DB+
BI_DA+
4
BI_DC+
BI_DD+
5
BI_DC-
BI_DD-
6
BI_DB-
BI_DA-
7
BI_DD+
BI_DC+
8
BI_DD-
BI_DC-
1000Base-T RJ-45 Port
Pin Number
Assignment
1
BI_DA+
2
BI_DA-
3
BI_DB+
4
BI_DC+
5
BI_DC-
6
BI_DB-
7
BI_DD+
8
BI_DD-
10/100 Base-T(X) RJ-45 Port
Pin Number
Assignments
1
TD+
2
TD-
3
RD+
4
Not used
5
Not used
6
RD-
7
Not used
8
Not used
IGS-9122GPM
