manualshive.com logo in svg

ORiNG IAR-142 Series, User Manual, Page: 57 / 57

Share
Download
ORiNG IAR-142 Series User Manual Download Page 57

IAR-142-/142+-3G  User  Manual 

 

 

ORing Industrial Networking Corp.                                                                                                56 

interference, 

and (2) this device must accept any interference, including interference that may cause 

undesired operation of the device. 

 

L'opération est soumise aux deux conditions suivantes: (1) cet appareil ne peut causer 

d'interférences,et  (2)  cet  appareil  doit  accepter  toute  interférence,  y  compris  celles 

susceptibles de provoquer fonctionnement du dispositif. 

To  reduce  potential  radio  interference  to  other  users,  the  antenna  type  and  its  gain 

should  be  so  chosen  that  the  equivalent  isotropically  radiated  power  (e.i.r.p.)  is  not 

more than that permitted for successful communication. 

 

Afin de réduire les interférences radio potentielles pour les autres utilisateurs, le type 

d'antenne  et  son  gain  doivent  être  choisie  que  la  puissance  isotrope  rayonnée 

équivalente (PIRE) est pas plus que celle premise pour une communication réussie 

 

RF  exposure  warning: The  equipment  complies  with  RF  exposure  limits  set  forth  for 

an  uncontrolled  environment.  The  antenna(s)  used  for  this  transmitter  must  not  be 

co-located or operating in conjunction with any other antenna or transmitter. 

 

Avertissement  d'exposition  RF:  L'équipement  est  conforme  aux  limites  d'exposition 

aux  RF  établies  pour  un  incontrô lés  environnement.  L'antenne  (s)  utilisée  pour  ce 

transmetteur  ne  doit  pas  être  co-localisés  ou  fonctionner  en  conjonction  avec  toute 

autre antenne ou transmetteur. 

 

 

 

 

Summary of Contents for IAR-142 Series


























































Reviews:

No comments