ORiNG IAR-142 Series User Manual Download Page 11 | Manualshive

Page: 11 / 57

ORiNG IAR-142 Series User Manual Download Page 11

IAR-142-/142+-3G User Manual

ORing Industrial Networking Corp. 10

The screws should be 6mm diameter head x 3mm diameter thread, as

shown below. Note that the screws should not be larger than the size

used in the series to prevent damaging the router.

3.3 Wiring

WARNING

Be sure to switch off the power and make sure the area is not hazardous
before disconnecting modules or wires. The devices may only be connected to
the supply voltag shown on the type plate.

3.3.1 Grounding

Grounding and wire routing help limit the effects of noise due to electromagnetic interference

(EMI). Run the ground connection from the ground screw to the grounding surface prior to

connecting devices.

3.3.2 Dual Power Inputs

The router has two sets of power inputs, power input 1 and power input 2, on a 4-pin terminal

block on the router

’s top panel. Follow the steps below to wire redundant power inputs.

Step 1

: insert the negative/positive DC wires into the V-/V+ terminals, respectively.

Step 2

: to keep the DC wires from pulling loose, use a small flat-blade screwdriver to tighten

the wire-clamp screws on the front of the terminal block connector.

Note

: besides power input, the router can also be powered by a PoE PSE such as switch via

its PoE-enabled WAN port.

«
...
9
10
11
12
13
...
»

Summary of Contents for IAR-142 Series


























































Reviews:

No comments