5
Operating Recommendations
This new ORECK XL High-Speed Upright is one of the finest, fastest,
and strongest units in its class. You’ll love the way it cleans, gets under
things, and it’s SO lightweight and easy to use.
The following are a few simple suggestions regarding its operation:
1. When inserting a new disposable paper filter dust bag—FIRST
PUFF OUT and OPEN THE BAG.
2. When the disposable filter dust bag is full, REPLACE IT.
3. If at any time the machine does not pick up properly or makes an
unusual noise, STOP OPERATION and service.
4. Although your upright will pick up pins, paper clips, and other
small objects, it is recommended that these be removed from the
floor before you vacuum. Failure to do so may result in permanent
damage to the motor suction fan and its housing.
5. WARNING: Do not use your vacuum cleaner on damp or wet
surfaces. This will cause damage to the vacuum cleaner and is
dangerous to the user. Damage caused by use on wet or damp
surfaces is not covered under warranty.
6. REPLACE THE BELT EVERY 6 MONTHS.
7. Change the disposable filter dust bag at least once a month—
even if it is not full! The collected dust in the dust bag can cause
odor, attract moisture, and can affect the efficiency of the cleaner.
8. DO NOT run the vacuum cleaner over the cord. The revolving
brush could damage the cord.
9. Use caution when vacuuming over area rug edges and fringe.
General Information
The performance of your new cleaner greatly depends upon care and
maintenance. The instructions in this manual will guide you in
performing basic care and maintenance. To obtain the most satisfying
years of service read the instructions and keep them handy for future
reference.
Disposable Paper Filter Dust Bags
Disposable paper filter dust bags play a very important role in the
efficiency of your ORECK vacuum cleaner. The purpose of the paper
bag is to trap dirt, but at the same time it must be porous enough to
allow air to pass through. If the paper bag becomes clogged, no air can
pass through the cleaner and cleaning cannot take place, regardless of
the cleaner’s power.
To keep your cleaner operating at maximum efficiency, change the dust
bag frequently. DO NOT FILL ABOVE THE LINE INDICATED ON THE
DUST BAG.
Be sure the disposable paper filter dust bag is installed properly.
All paper dust bags are not the same. Your ORECK disposable
dust bags have been designed to be used with the ORECK cleaner.
Using bags other than genuine ORECK TYPE CC disposable bags
will affect the cleaning ability of your cleaner and could cause
damage to it.
The Belt
The belt on your vacuum cleaner controls the speed of the revolving
brush and is very important for the effective operation of the cleaner. If
the belt becomes stretched or cut, it will cause the revolving brush to
stop completely or slow down. See instructions in the manual for
replacing belt.
An extra belt is stored in the baseplate of your cleaner. When
buying replacement belts, use ONLY ORECK genuine belts. Belts
other than ORECK belts will not operate the revolving brush
correctly and may create undue stress which will cause damage to
the motor and brush bearings. Using belts other than ORECK belts
will void the warranty.
Lubrication
The vacuum cleaner motor bearings are factory lubricated and sealed.
Further lubrication is not required.
Parts List
To assist you in identifying components of your vacuum, the parts have
been numbered as follows:
1
Handle Tube, upper
2
Tube, lower
3
Power head
4
Outer bag
5
Paper filter dust bag
6
Power cord
7
Retaining spring
8
Bag tension bar
9
Zip fastener
10 On/off switch
11 Cord dump
12 Plastic loop / cable clamp
13 Connector assembly
14 Fan housing
15 Cord assembly
16 Cord strain relief assembly
Assembly
fig. 1
Before assembling appliance, remove two screws from connector
assembly. Remove cardboard insert by pulling upward.
fig. 2
With ON/OFF switch facing the front of the unit, slide upper
handle section over matching section of the connector assembly.
Hold tab of cord strain relief flush with TOP hole in connector
assembly. Insert screw through hole in tab of cord strain relief
and firmly tighten to connector assembly. Insert remaining screw
in botom hole of connector assembly and tighten firmly.
NOTE: The power cord comes installed in the cord strain relief.
Should the power cord come loose, simply pinch the power cord
together and slide approximately 1 - 2 inches through hole in
cord strain relief. Carefully slide power cord over clamp on the
the cord strain relief and pull excess until the power cord is
tightly rested under clamp.
fig. 3
Attach cord to cord clip by pressing cord above and below clip
ensuring the cord is fully rested in clip.
Operating Instructions
Make sure disposable paper filter dust bag is in place. DO NOT operate
the cleaner without a paper filter dust bag. Plug the power cord into an
electrical outlet and press the ON (l) - OFF(O) switch on Helping Hand
®
when ready to operate.
Up-Position Lock
fig. 4 Place foot on power head and lean handle back gently to release
lock for vacuum use. Return handle to the full upright position to
engage lock.
NOTE: Do not operate the unit while in the upright and locked position.
Do not let the unit run while in any one stationary position for any period
of time. Keep the unit moving while in operation.
For Easy Power Cord Storage
fig. 5 Wrap power cord around cord dump on Helping Hand
®
handle
and cord hook on connector.
fig. 6 To release cord, twist cord dump located on Helping Hand
®
handle 1/2 turn. Slide cord off handle.
1
2
3
4
9
10
11
14
15
16
12
13
5
6
7
8
